Chimney chase cover replacement for homes in Buena Vista
Framing damage under the old cover is shown to you and priced on its own line.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Chase cover faults worth a call in Buena Vista
- Rust streaks down the chase siding
- Ceiling stain near the fireplace
- Paint peeling off the metal top
- Cover smaller than the chase top
Jump to
Building a chase cover that sheds water
Listed chase top flashing with a made-to-measure cover
Some chimney makers supply a chase top flashing as part of the listed system. Where the chase is larger than that part, the instructions show it fixed to a bigger field-made cover. Screws or rivets hold it, and a sealant that stays flexible closes the joint.
That arrangement combines a listed piece at the pipe with a cover made to fit the box. We check whether your chimney uses one and whether it is still sound. If it is, the new cover can be built around it. If it is not, we look for the maker's current part before fabricating anything.
Keeping or replacing the cap on the pipe
The chimney pipe above the cover ends in its own cap. During a cover replacement, that cap usually has to come off and go back on. If it is sound and is the cap listed for that chimney, reusing it makes sense.
If it is corroded, bent or not the right cap for the system, we note it as a separate line. Chimney makers specify the cap for their pipe, so a replacement comes from the same system or an approved equivalent. The estimate shows whether the cap is being kept or replaced and why.
Cap height above the new cover
Chimney instructions can set how far the cap on the pipe must sit above the chase top flashing. A new cover built higher or with a taller collar than the old one can change that distance. So can a chase whose top has been built up during framing repair.
We check the cap height against the chimney instructions once the new cover is planned. If the pipe needs an extra section to keep the right height, we explain it before ordering. That part comes from the chimney's own system, and it appears on the estimate as its own item.
Galvanized chase covers in salty air
Zinc-coated steel loses its coating sooner when sea air deposits chlorides on it. Published corrosion data puts warm marine exposure close to industrial exposure for galvanized steel, with wind and shore distance moving the rate up or down.
For a chase close to the shore, galvanized sheet is still possible, but it deserves an honest comparison with the alternatives. We set out how each metal is likely to weather in that exposure and what upkeep it will need. The estimate names the metal we suggest and the reason for it.
What a chase cover proposal should list
- Pipe hole position and diameter
- Skirt depth over the chase walls
- Cover metal and gauge named
- Air spaces at the pipe kept open
Chase cover questions worth asking in Buena Vista
Why is there a gap between the storm collar and the cover?
Some chimney systems call for air spaces at the chase top so the chase stays ventilated around the pipe. Where the instructions show them, those gaps are part of the design, not a fault, and we keep them when fitting the new cover.
What should I tell you when I call about the chase?
Describe what you see from the ground, any stains or water inside and whether the fireplace is used. Mention the chimney maker if you know it. With that, we can plan the visit to your home in Buena Vista and bring the right gear.
Who handles a leak that comes through the chase siding?
If water enters through the siding or stucco rather than the top, that is chase repair rather than cover replacement. We trace the water path and tell you which part lets it in, so the estimate addresses the actual entry point.
More Ways to Care for Your Fireplace
- Hurricane and Storm Damage Chimney RepairAssess storm-related chimney concerns and distinguish temporary protection from permanent component repair.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo