Stainless chase covers fitted in Liberty City
Framing damage under the old cover is shown to you and priced on its own line.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What a worn chase cover looks like in Liberty City
- Rust flakes inside the fireplace
- Gap around the pipe collar
- Paint peeling off the metal top
- Metal banging on the chase in wind
Jump to
Chase cover replacement explained for Liberty City
Where the pipe sits on the top
The pipe may not sit in the center of the chase. Framing, offsets and the fireplace below all push it one way or another. The hole in the new cover has to match where the pipe really is, not where it would look neat.
We measure the pipe position from two sides of the chase. If the pipe has shifted or leans, we note that, because it may point to a support problem inside the chase. The estimate shows the hole position, and any concern about the pipe is described separately for you to decide on.
Soft siding just below the top edge
If the siding near the top of the chase feels soft, looks swollen or has paint bubbling off it, water has probably been getting behind it. The top few courses are usually the first to show it, because they sit right under the edge of the cover.
Do not press or pry at it from a ladder. Tell us what you see, and we look at it during the inspection. Siding and sheathing repair belong to chase repair, which is quoted separately from the cover. Replacing the cover without dealing with soaked wood beneath it leaves the problem in place.
The order a chase cover job follows
A chase cover job follows a simple order. We confirm the chimney system, measure the chase and check what we can see. Once the old cover is off, any framing or sheathing repair you approved is done. Then the new cover goes on, followed by the storm collar, sealant and cap.
That order keeps the new cover from being fastened onto damaged wood or fitted around a pipe that needs attention. If your job has several stages, the estimate shows them in sequence. We explain any waiting time between stages before you approve.
Checking a chase top more often near the water
A chase cover near the coast works harder than the same cover inland. Salt deposits collect on the metal and in the seams, and rain may not rinse them off. Sealant, fasteners and corners tend to show wear sooner.
In that exposure, a maintenance visit that includes the chase top is worth considering more often. We look at the corners, the collar, the storm collar and the screws. Tell us how close the house is to open water and which side takes the wind. That helps us decide what to look at first.
Parts of the chase job priced separately
- Skirt depth over the chase walls
- Drip edge along the skirt
- Cover metal and gauge named
- Old cover and fasteners removed
Chase cover replacement questions in Liberty City
Is the fireplace safe to use while the chase leaks?
Water in a chase can reach the chimney pipe and the fireplace below it. If you see water inside or fresh corrosion in the firebox, stop using the fireplace and have the chase top and chimney checked before the next fire.
Should I paint my old chase cover to slow the corrosion?
Paint can slow surface corrosion on a cover that is otherwise sound, but it does not close holes or fix a flat top that holds water. We tell you honestly whether paint is worth it or the cover is past that point.
Who handles a leak that comes through the chase siding?
If water enters through the siding or stucco rather than the top, that is chase repair rather than cover replacement. We trace the water path and tell you which part lets it in, so the estimate addresses the actual entry point.
More Ways to Care for Your Fireplace
- Chimney Crown RepairRepair the damaged chimney top with an approach matched to the crown and supporting masonry.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo