Chase cover repair or a new cover in Pinewood
The estimate names the metal, the gauge, the collar and how the cover is fastened.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Chase cover trouble visible from the yard
- Water pooling on top of the cover
- Gap around the pipe collar
- Paint peeling off the metal top
- Cover shifted after a strong storm
Jump to
The chase cover job, from measure to seal
The chimney listing decides the top details
Under the Florida Building Code, a factory-built chimney must be installed and terminated as its manufacturer's instructions say. That rule reaches the chase top, because the pipe, the collar parts, the storm collar and the cap all belong to the chimney system.
The cover itself is often made to measure, but it has to respect the chimney instructions where the pipe passes through. We read those instructions, or the maker's current version, before specifying the cover. If the chimney cannot be identified, we tell you and explain how we would proceed safely.
Paperwork for a factory-built chimney
A framed chase usually hides a factory-built chimney, and the paperwork for it can save time. The installation manual, the fireplace model details or an old invoice can tell us the chimney maker and which parts belong at the top.
Nothing on file is fine too. The chimney label and the parts themselves usually tell us enough. Where papers exist, they help us order the right storm collar or cap and follow the correct instructions for the collar and air spaces.
New siding and the cover skirt
When a chase is re-sided, the new finish can change the outside size of the chase. A cover that fitted the old siding may now be too tight to lap over the new, or leave a gap where the skirt used to sit.
If you are planning new siding or stucco on the chase, it is worth coordinating the cover with that work. We can measure once the new finish is on, so the skirt laps it properly. Tell us about any planned exterior work when you call, and we plan the timing around it.
Shields at the top of the chase framing
Inside the top of the chase, some chimney systems use metal shields around the pipe to protect nearby framing. One maker's instructions place roof radiation shields at the top of the chase and state that they do not allow reduced clearances.
When the old cover is off, we can see whether the shields and spacers the chimney calls for are in place. If they are missing or damaged, we tell you. Any parts needed come from the chimney system, and they are priced separately from the cover.
Your chase cover quote in Pinewood, itemized
- Air spaces at the pipe kept open
- Written record of the cover work
- Workmanship warranty on the fitting
- Water path from the old cover traced
Chase cover FAQs for homes in Pinewood
How can I tell whether my chimney has a chase cover?
If the chimney is a boxed structure finished in siding or stucco with a metal pipe at the top, it has a chase and almost certainly a cover. A brick or block chimney with clay flues has a crown instead. We confirm which during the free inspection.
Can a corroded cover be patched rather than replaced?
Small repairs can buy time on a cover that is otherwise sound. A cover with holes, a dished middle or thin metal throughout usually needs replacing, because patches over corrosion tend to trap water. We show you the condition before you choose.
Will a new chase cover fix rotted wood in the chase?
No. The cover stops new water from entering, but rotted sheathing or framing needs its own repair. We note that damage separately, often once the old cover is off, and you decide on it before the chase is closed.
More Ways to Care for Your Fireplace
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
- Ventless Gas Fireplace ServiceService the identified vent-free appliance without bypassing its required safety components.
- Chimney Animal RemovalAssess occupied chimney openings and plan appropriate follow-up cleaning or entry protection.
- Stone Chimney RepairRepair affected stone chimney surfaces with the supporting construction and visual match considered together.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo