Chimney cap installation on homes across Edgewater
We fit caps to clay tile, metal liners and factory-built pipe, each by the method it calls for.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs a chimney cap in Edgewater needs work
- Rain dripping onto the fireplace floor
- Cap lid lifted, dented or loose
- One flue capped and another left open
- Old cap glued or siliconed in place
Jump to
What goes into a new chimney cap in Edgewater
How a listed metal cap is fastened
On a factory-built chimney, the cap usually fits onto the last pipe section and is fixed with the screws supplied for it. One maker's instructions also warn against pressing down on the top of the cap, because that can damage it. Push from the lower part instead.
Details like these are why we work from the instructions rather than habit. A cap fastened with the wrong screws, or seated by force, can loosen in wind or bend its own lid. We fit the listed cap the way its maker describes. The fastening method then goes into the record of the work, so the next person knows what was done.
Replacing only the screen
Where the lid and frame are in good shape, a new screen can extend the life of a cap. The replacement has to come from the cap maker or match the original in fit and opening size, because the screen affects both sparks and draft. A roll of generic mesh wired into place is not the same repair.
We check whether a matching screen is available for your cap. If it is, the estimate lists it as a screen replacement rather than a new cap. If the maker no longer offers one, we explain why a whole cap may cost less trouble over time.
Separate caps on each flue
Where a chimney carries more than one flue, separate caps on each tile are an alternative to one large cap on the crown. Separate caps leave the crown undrilled and let each flue have the termination that suits it.
They also have limits. Flues set close together may not leave room for individual caps, and tiles in poor condition may not hold them. We compare both approaches for your chimney and show the reasoning on the estimate. Neither design wins on every chimney. The layout of the flues and the condition of the top decide it.
Checking the cap once it is fitted
Once the cap is on, we check that it sits square, that the fasteners are tight and that the lid height suits the flue. We look at the screen for any damage from handling and confirm that the lid or cap can be removed for cleaning.
If there is a way to confirm the draw safely during the visit, we do so, and we tell you what we observed. Any concern about the draft that remains is noted in the written record. You should not have to discover a problem with the new cap the first time you light a fire.
Line items on a chimney cap estimate
- Flue height above the crown
- Crown surface under a multi-flue cap
- Fastener type and fastening points
- Top course of brick under a band cap
Before you replace a chimney cap in Edgewater
Why does smoke come into the room after a cap was fitted?
A clogged screen, a lid set too low or a cap that is too small for the flue can hold smoke back. Stop using the fireplace and ask us to look at the cap and the flue before the next fire.
Will you need to drill into my chimney crown?
Only for caps that mount on the crown. Their flanges are fastened into the crown and kept back from its edge so the concrete does not crack. Caps that clamp to a flue tile or band around the brick need no drilling there.
What should I mention when I call about a cap?
Describe what you see from the ground, how the fireplace is used and whether anything else vents through the chimney. Mention recent roof work or strong storms. Those details help us plan the visit to your home in Edgewater.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo