Worn chimney cap replacement in Kendale Lakes
Our family team fits the cap, clears the roof area and hauls the old parts away.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs a chimney cap in Kendale Lakes needs work
- Rattling from the chimney top in wind
- Mesh screen torn, bent or missing
- Cap lid lifted, dented or loose
- Cap fasteners loose or missing
Jump to
How we fit a chimney cap in Kendale Lakes
Open area under the lid and the draw
A rain cap sits over the flue with open sides beneath its lid. The Florida Building Code sets a minimum for that open area, in proportion to the flue outlet the cap serves. A cap that is too small or sits too low can narrow the path the smoke has to take.
We size the cap against the flue it covers, not against the width of the chimney. Where one cap covers several flues, each flue still needs its own clear path out. If your fireplace smoked after an earlier cap was fitted, mention it when you call. That history tells us where to start looking.
Replacing only the screen
Where the lid and frame are in good shape, a new screen can extend the life of a cap. The replacement has to come from the cap maker or match the original in fit and opening size, because the screen affects both sparks and draft. A roll of generic mesh wired into place is not the same repair.
We check whether a matching screen is available for your cap. If it is, the estimate lists it as a screen replacement rather than a new cap. If the maker no longer offers one, we explain why a whole cap may cost less trouble over time.
Loose brick at the top of the chimney
The top course of brick takes the full force of the weather and often holds a cap. When its mortar joints open or the brick itself spalls, the course can loosen. A cap clamped around it or fastened near it then has little to hold.
We check the top course during the inspection by looking at the joints and the brick faces. Loose or damaged brick is noted as a masonry repair, separate from the cap. Fitting a new cap onto a loose course would only move the problem. The estimate shows the repair and the cap as two decisions.
Masonry hoods and other older cap types
Not every chimney top ends in a metal cap. Some older designs use a slab of stone or concrete set on piers above the flue, or a clay pot on the tile. These act as rain covers too, and they can crack, shift or lose their mortar over time.
If your chimney has one of these tops, tell us. We look at its condition and whether it still leaves enough open area for the smoke. Repairing it, replacing it with a metal cap or leaving it alone are all possible routes, and we explain the tradeoffs before you choose.
Chimney cap scope, item by item
- Flue height above the crown
- Mesh screen for sparks and animals
- Listed cap for a factory-built chimney
- Separate line for damper or chase cover work
Chimney cap answers for homes in Kendale Lakes
What happens if the flue tile is cracked under the cap?
A cap clamped to a cracked tile may not hold, and the crack can let water into the chimney. We list the damaged tile as its own line on the estimate so you can decide on that repair before the cap goes on.
Is a stainless cap a sensible choice over galvanized steel?
Each metal weathers in its own way, and the grade, the fasteners and the metals it touches matter as much as the name. We state the metal and fasteners on the estimate so you can compare proposals on equal terms.
Can a cap be fitted over a damper at the chimney top?
Some top-mounted dampers already act as a cap, and some are made to sit beneath one. The damper maker's instructions decide which. Tell us if your chimney has a cable-worked damper at the top so we check it before recommending a cap.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo