Crown sealing and crown rebuilds for chimneys in Bal Harbour
A crown should shed water off the chimney top, and we repair or replace it so it does that job again.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Crown damage worth mentioning when you call
- A crack running outward from a flue
- Dried or split caulk around the flue
- Sections of crown that look lifted
- Brick joints washing out just below the top
Jump to
Crown repair choices for homes in Bal Harbour
Reading the crown from the ground
You can learn a lot about the crown without climbing. Look for chunks of concrete in gutters or on the roof near the chimney. Look for dark streaks down the brick just below the top, or a patch of growth that stays green on the crown.
Brick industry maintenance guidance suggests binoculars for looking at high masonry. They help here too. Note what you see and tell us when you call. Leave the roof to us, because a steep or slick surface is not worth the risk for a closer look.
The written record after crown repair
When the job is done, you receive a written record of the work. It says what was removed, what was applied or formed, and how the flue joints were sealed. It also notes anything we saw that falls outside the crown.
Keep it with your home papers. If you sell the house, change contractors or call us about the chimney again, the record shows what was done at the top. It also makes a later assessment more specific, because nobody has to guess what material is up there.
Letting a wet crown dry before sealing
A crown that has been soaking up water may stay damp inside long after the surface looks dry. Sealing over that moisture can trap it. The coating maker's instruction to avoid wet or saturated surfaces reflects this.
If your crown has been holding water, we check how it looks and feels before proposing a coating date. Sometimes the answer is to clear drainage and wait. Sometimes the crown is too far gone and replacement is the better plan. We explain what we see rather than rushing a coat on.
Chimney crown work for homes in Bal Harbour
Chimney crown repair for homes in Bal Harbour follows the same careful order on every job. We identify the top, check whether it is firm and sloped, and look at every flue joint. Then we explain whether the crown can be sealed, repaired or should be replaced.
You see the findings before any work begins. The estimate keeps crown work apart from the cap, the flue and the brick below. When the job is finished, the debris is gone, the flue joints are sealed and you have a written record of what was done.
Crown work we price line by line
- Sealant joint around the flue tiles
- Earlier patches and coatings identified
- Protection for roof covering and brick faces
- Mortar wash assessment and removal
Chimney crown questions we hear
Do you seal the crown and the chimney brick at the same visit?
They are separate products and decisions. A crown coating treats the top surface. A water repellent for brick is considered only after cracks and joints are repaired, and it should let the masonry breathe. Each appears as its own line.
Is there a better time of day for crown coating work?
The product data sets temperature limits and asks for a dry surface with no rain due. On hot days we may work earlier or later so the coating goes on within those limits. We confirm timing when we schedule.
Can a bond break be added to a crown that lacks one?
On an existing crown, the practical step is opening the joint at each flue liner and sealing it properly with backer material and elastomeric sealant. On a new crown, the bond break is built in. We explain which applies after inspection.
More Ways to Care for Your Fireplace
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Chimney WaterproofingTreat suitable chimney masonry after checking the surface, repair needs and product requirements.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Ventless Gas Fireplace ServiceService the identified vent-free appliance without bypassing its required safety components.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo