Crown sealing and crown rebuilds for chimneys in Ives Estates
You receive a written record of the crown work, including what was removed and what was applied.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Crown damage worth mentioning when you call
- Hairline cracks across the crown surface
- Concrete chips in the gutter
- Dried or split caulk around the flue
- A crown patch that has cracked again
Jump to
How we approach crown repair in Ives Estates
Coating within the maker's temperature limits
The data sheet for a brushable crown coating sets an upper limit for surface and air temperature at the time of application. A roof in strong sun can run hotter than the air around it. Working outside that range goes against the product instructions.
On hot days we may schedule coating for the cooler part of the day. We would rather move the start time than push a product outside its instructions. If you have a preference for arrival windows, tell us when booking and we will explain what the product allows.
Coordinating crown work with roof work
Crown repair and roof replacement both happen at the top of the house. The order matters. New roofing damaged by crown removal, or a new crown disturbed by roofers, means repeat work for someone.
If roof work is planned, tell us the timing. We explain whether the crown should be done before or after, and how the two trades can avoid working over each other. The flashing where the chimney meets the roof often sits between the two jobs, so we clarify who handles it.
Letting a wet crown dry before sealing
A crown that has been soaking up water may stay damp inside long after the surface looks dry. Sealing over that moisture can trap it. The coating maker's instruction to avoid wet or saturated surfaces reflects this.
If your crown has been holding water, we check how it looks and feels before proposing a coating date. Sometimes the answer is to clear drainage and wait. Sometimes the crown is too far gone and replacement is the better plan. We explain what we see rather than rushing a coat on.
What to watch after crown repair
After the work, keep an eye on the chimney during the next few heavy rains. Look for new stains inside, drips at the fireplace or streaks under the crown. Those are the places a remaining problem would show.
If you notice anything, write down when it appeared and what the weather was doing. Call us and describe it. Your written record shows what was done, so we can check the repaired top and any other part that could be involved. Fine lines on new concrete are discussed rather than ignored.
Crown work we price line by line
- Slope and drainage off the top
- Bond-break layer under new concrete
- Written record of completed crown work
- Upfront price for each crown item
Answers about chimney crown work
Will a new cap stop water coming through the crown?
No. A cap covers the flue opening, while the crown covers the masonry around it. Water that enters through a broken crown keeps entering under a new cap. We check both parts and price each one on its own line.
What does the free inspection include for a chimney crown?
We look at the crown surface, edges, slope, overhang and the seal at every flue, plus the cap fixings and the brick just below. You hear the findings on site and receive a free written estimate that keeps each item separate.
Can a bond break be added to a crown that lacks one?
On an existing crown, the practical step is opening the joint at each flue liner and sealing it properly with backer material and elastomeric sealant. On a new crown, the bond break is built in. We explain which applies after inspection.
More Ways to Care for Your Fireplace
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
- Chimney WaterproofingTreat suitable chimney masonry after checking the surface, repair needs and product requirements.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo