Repairing chimney counter flashing in West Little River
A roof junction repaired properly once, rather than patched again after the next heavy rain.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Early flashing warnings at homes in West Little River
- Gaps along the top edge of the metal
- Stain returning after an earlier patch
- Nail heads showing through the flashing
- Leaves and grit piled behind the chimney
Jump to
How we repair the flashing at your roof line
Base and counter flashing work as a pair
Flashing at a chimney is usually two layers of metal rather than one. The base pieces lie on the roof and turn up against the brick. The counter flashing comes down from the chimney and laps over them. Because the two layers overlap instead of joining, each one stays with its own surface.
When we assess the junction on a home in West Little River, we check both layers separately. A sound base piece under a loose counter piece needs a different repair from the reverse. The estimate names which layer fails and on which face, so you can see why the scope is sized the way it is.
What the workmanship warranty covers
Our flashing work carries a workmanship warranty. It covers the flashing we installed and the way we installed it, as described in the written record. It does not extend to parts of the roof or chimney that were outside the agreed scope.
That is one reason the scope matters. If the estimate says the crown or the masonry face was left as found, the warranty follows that line. Ask us before you approve how a later leak would be looked at, and we will explain how we separate our work from other sources.
Fasteners and metals that do not mix
When two different metals touch in wet conditions, one of the pair tends to corrode sooner than it would alone. That applies to flashing pieces and to the nails or screws that hold them. A steel fastener in copper flashing, for example, can fail early.
We match fasteners and any joining pieces to the flashing metal we install. Where new flashing has to meet old metal of a different kind, we explain how the contact is handled. If an earlier repair mixed metals, that is noted in the findings so you know why those pieces are included.
Water that appears without rain
If water or a damp patch appears near the chimney on a dry day, the flashing is probably not the cause. Flashing keeps out rain. Water without rain may come from plumbing, cooling equipment, condensation or something else in the attic.
Tell us if you have seen dampness in dry weather. We still check the flashing, but we also say when the evidence points away from the chimney. That can save you from paying for a roof junction repair that would not change anything.
The flashing scope, item by item
- Underlayment at the chimney face
- Flashing metal named in writing
- Debris cleaned up and hauled away
- Openings covered at the end of each day
What people ask about chimney flashing
How do you know the flashing is the source of the water?
We compare where the water appears with what we see at the junction, in the attic and at the top of the chimney. When the evidence is unclear, a hose water test may help if the job calls for it. The findings say what points where.
Should I paint over the ceiling stain now?
Wait until the flashing repair is done and the area has dried. A fresh coat of paint makes it harder to tell whether the stain is still growing. If the mark spreads after the repair, tell us promptly so we can look again.
Will the new sealant line match my mortar color?
It may not match exactly at first. We can discuss a sealant color closer to the mortar, and new mortar at a recut joint may tone down as it weathers. Water tightness comes first, but tell us if appearance matters.
More Ways to Care for Your Fireplace
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo