Chimney inspection in Coral Terrace, explained at the hearth
Findings explained before we leave, concealed parts named as concealed, and a free written estimate for any work.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Changes worth an inspection visit
- A rusted or stuck damper
- A strong storm has passed through
- Flaking brick faces on the chimney
- Rust stains running down the chimney
Jump to
From hearth to crown, the inspection explained
Inspecting the crown at the top of the chimney
The crown is the top surface of a masonry chimney that sheds water away from the flue. The Florida Building Code's chimney chapter describes it as sloped, with a way for water to drip clear of the walls. Cracks and gaps around the flue let water in, and a flat top holds it there.
We look at the crown when the roof can be reached safely. Hairline cracks and wide splits lead to different repairs, and we explain which one applies. If the crown cannot be reached, the record says so and we explain what that leaves unknown.
Mixed brands of chimney parts
The sections of a factory-built chimney are made to fit parts from the same listed system. A section, cap or support from a different brand may not have been tested with the rest. That can affect clearances and how the joints seal.
When we see parts that do not match, we note where they are and what they are. We explain why it matters and what the manufacturer's instructions expect. Correcting it is a separate repair, priced after we identify which parts are listed for your system.
Flues that serve another appliance
A chimney may carry a flue for an appliance other than the fireplace. The Florida Building Code's fuel gas volume covers how gas appliances vent through chimneys. Each flue should serve the equipment it was built or lined for.
We identify each flue and what connects to it, as far as access allows. If a gas appliance vents into the chimney, we note the condition of its flue and the top. We also tell you when the appliance itself needs a gas service visit. We do not guess at connections we cannot see.
Whether the flue suits the fireplace opening
A flue has to be large enough for the opening it serves, or smoke can spill into the room. The Florida Building Code's chimney chapter relates the flue area of a masonry fireplace to the opening it serves. A mismatch often shows up as smoke at the start of each fire.
We compare the flue and the opening during the inspection and explain the relationship without quoting figures. If they do not suit each other, the options range from small changes at the opening to relining. Each option is explained with its trade-offs.
Inspection scope for homes in Coral Terrace
- Deposits and blockages in the flue
- Each flue matched to its appliance
- Concealed parts named as concealed
- Findings ranked by effect on use
Chimney inspection questions asked in Coral Terrace
What if part of the chimney cannot be seen?
We tell you which part, why it could not be seen and whether it matters for your question. The written record lists it. If more access is needed, we explain what it would involve and what it would cost.
Do you go up on the roof during an inspection?
When the roof can be reached and walked safely, yes, because the crown, cap and flashing are often where problems start. If it cannot, we look from the ground or a ladder and say what that view could not show.
Does the inspection include looking at the flue lining?
Yes, along the length that can be seen from each end. We note cracks, open joints, missing sections and heat damage, and we say how far the view reached.
More Ways to Care for Your Fireplace
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Fireplace RestorationCoordinate fireplace repairs while preserving suitable existing features and defining the intended use.
- Chimney Cap Installation and ReplacementProtect the chimney opening with a cap chosen for its fit, attachment and compatible system.
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo