Listed chimney liners installed in Edgewater
A liner chosen for the appliance you actually plan to run in Edgewater, not for the last one.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When a flue lining deserves attention in Edgewater
- A metal liner with no label
- A planned switch from gas to solid fuel
- A liner cap that no longer fits
- A stale odor drifting from the flue
Jump to
Liner planning for homes in Edgewater
Insulation follows the listing, not a habit
Whether a liner needs insulation depends on the listed system and the chimney it goes into. Some systems require an insulation wrap over part or all of the run. Others arrive insulated from the factory. The listing also ties the liner's clearances to how it is installed.
We read the insulation requirement from the manual of the liner we propose. The estimate says whether insulation is included, what type, and why. Leaving it out to lower a price, or adding it where the listing does not call for it, is not a choice we make on your behalf.
Gas-fired appliances and the fuel gas chapter
When a gas-fired appliance vents into a masonry chimney, the Florida Fuel Gas Code chapter on chimneys and vents applies. It accepts clay lining, a lining system listed to the chimney liner standard, or other approved material. It also recognizes liners listed for gas service only, which carry their own labels.
Tell us the fuel and the appliance type before we plan the liner. A liner chosen for solid fuel is not automatically right for a gas-fired appliance, or the reverse. The appliance manual and the liner listing together decide it, and we show both in the proposal.
Coordinating the liner with the appliance installer
Sometimes a different company installs the appliance while we install the liner. Both sides need the same information about the connector, the tee or adapter, and the clearances in the room. Gaps between two scopes are where mistakes hide.
Ask us to write down exactly where our liner work ends. We describe the connection we make and what the appliance installer should expect to find. If questions come up about the appliance itself, its manual and its installer answer them, and we say so plainly. Share our written scope with the appliance installer before either visit.
An existing chimney cap and a new liner
If the chimney already has a cap over the flue, it may need to come off for relining. A cap over a single flue is usually replaced by the liner's own cap. A cap covering several flues may stay if it clears the new top parts.
We explain what happens to the existing cap and whether it is reused. If it is damaged, replacing it is listed separately. The goal is one clear arrangement at the chimney top, described in the estimate before work begins. A cap that stays is checked for damage and fit.
Relining scope for a home in Edgewater
- Top plate and clamp assembly
- Liner cap with its spark screen
- Lower end transition above the smoke chamber
- Old liner removal and disposal
More about relining your chimney in Edgewater
How do you decide what size liner my chimney needs?
We start from the appliance manual, which states the flue size the appliance requires, and the code rule that a flue may not be smaller than the appliance connector. Then we check whether the passage can take that size along its whole route.
Can two appliances share a single new liner?
Only where the appliance instructions, vent listing and applicable requirements permit a properly sized common vent. Some systems require separate flues. We identify every connected appliance before specifying the liner; the space outside the liner cannot be used as another vent.
How does the discount after the free inspection work?
When you book the relining no more than 72 hours after your free inspection, a 10% discount applies to the agreed work. The window starts from your own inspection, and the estimate shows the figure before you decide.
More Ways to Care for Your Fireplace
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Hurricane and Storm Damage Chimney RepairAssess storm-related chimney concerns and distinguish temporary protection from permanent component repair.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo