Chimney liner installation for fireplaces in Highland Beach
If your flue can be repaired rather than relined, we explain that option before quoting a liner.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What points toward a new chimney liner
- A metal liner with no label
- Rust holes in an old liner
- A crushed or kinked liner section
- A liner cap that no longer fits
Jump to
How we plan a chimney liner in Highland Beach
A relining plan starts with a free inspection
The free inspection is where the relining question gets answered with evidence. We look at the appliance, the connection, the accessible parts of the flue and the chimney top. From that we can say whether a liner is the right step and what it would involve.
If a liner is not the right step, you hear that too. Sometimes the problem belongs to another part of the chimney. Relining that you approve inside 72 hours of the free inspection is priced at 10% off, and the estimate shows that figure before anything starts.
The chimney top at the end of each work day
A relining job can take more than one visit, especially when preparation is heavy. Between visits the top of the chimney may be open. Before we leave each day, the open chimney top is closed off so rain and debris stay out.
Inside, the fireplace area is protected while we work and left clean when we leave. Debris from tile removal or old liner parts is cleaned up and hauled away. Ask us what the room will look like between visits if the job runs longer than planned.
Appliances that need their own vent system
Some appliances are designed to push their flue gases out under pressure, or to condense them. The chimney liner standard's scope excludes those types, and their manuals specify the vent systems they need. A chimney liner is not a substitute.
If your appliance is one of these, relining may not be the answer at all. We explain what the manual calls for and whether any of it is work we do. Knowing this before an estimate avoids paying for a liner the appliance cannot use, and it keeps the conversation on the right equipment.
Reading the appliance rating plate
Most appliances carry a label with the model, the fuel and the venting type. That label is where liner sizing and material choices begin. It may sit on the back, under a trim piece or inside a door.
If you can see it without moving anything, read it to us when you call or keep it ready for the visit. Do not open panels or shift a hot or connected unit to reach it. We can locate it during the inspection if it is hard to see.
Liner scope written out in full
- Cleaning of the existing flue
- Glazed deposit removal where found
- Written record of the liner installed
- Start-up guidance from the appliance manual
Flue liner answers before you approve
Does the new liner need insulation around it?
Only the liner's listing can answer that. Some systems require insulation on part or all of the run, some come insulated, and some rely on the space around them. We read the requirement from the manual and state it in the estimate.
Why does the estimate list cleaning separately from the liner?
Liner makers ask for the existing flue to be inspected and cleaned before relining, and the effort varies from chimney to chimney. Listing it separately shows you what the preparation involves and what it adds to the total.
Do you install liners for open fireplaces as well as appliances?
Yes. For an open masonry fireplace, the code sizes the flue against the fireplace opening, so the calculation differs from an appliance. We explain which rule set the size in the estimate, along with how the liner leaves the smoke chamber.
More Ways to Care for Your Fireplace
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Fireplace RestorationCoordinate fireplace repairs while preserving suitable existing features and defining the intended use.
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo