Chimney liner installation for fireplaces in Palmetto Bay
Free inspection first, then a written relining estimate with each part and each preparation step on its own line.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Liner warning signs worth a closer look
- Smoke spilling at the appliance door
- A metal liner with no label
- Rust holes in an old liner
- Water reaching the appliance from above
Jump to
The liner work behind a sound flue in Palmetto Bay
Why a masonry flue has to carry a lining
The Florida Building Code's chimney chapter says a masonry chimney shall be lined. It also asks that the lining match the appliance connected to it, following that appliance's listing and the maker's instructions. Relining is therefore not a cosmetic upgrade. It restores a condition the chimney is expected to meet.
Our first question is what the flue serves. A fireplace, a solid-fuel appliance and a gas-fired appliance can each point to a different system. Tell us what burns at the bottom of the chimney, and we explain which lining options fit before any material is chosen.
What to mention when you ask about relining
A few details make the first conversation more useful. Mention the appliance make and model, the fuel, and whether it vents into the fireplace opening or through the chimney wall. Say whether an earlier visit recommended relining, and why.
Describe any smoke, odor or draft problem and when it happens. Old invoices or liner paperwork help identify what is already there. With that information, the free inspection in Palmetto Bay can focus on the questions that matter for your chimney. Even a rough idea of when the problem started is useful.
How a relining job is scheduled
A straightforward relining can be finished in one visit, while heavy preparation may need more. We explain the expected sequence when you approve the estimate. The fireplace or appliance is out of use while the flue is open.
Ask what each visit covers and what state the chimney is left in between. The top is covered at the end of each work day. If weather or a discovery changes the plan, we tell you and agree the next step before continuing. Access to the room and the roof is agreed ahead of each visit.
A new liner for an ageing appliance
Relining for an appliance that is near the end of its life deserves a pause. The liner should suit the appliance you will actually run. If a replacement is likely soon, sizing for the current unit may not serve you well.
We explain the liner options for the current appliance and what would change with a different one. The choice is yours, and the estimate says which appliance it assumes. Replacing the appliance itself sits outside our relining estimate. If you replace it later, the liner may need to change with it.
What a liner estimate should spell out
- Top plate and clamp assembly
- Written record of the liner installed
- Support method for the liner run
- Start-up guidance from the appliance manual
Chimney liner questions, answered plainly
How do you decide what size liner my chimney needs?
We start from the appliance manual, which states the flue size the appliance requires, and the code rule that a flue may not be smaller than the appliance connector. Then we check whether the passage can take that size along its whole route.
How does the discount after the free inspection work?
When you book the relining no more than 72 hours after your free inspection, a 10% discount applies to the agreed work. The window starts from your own inspection, and the estimate shows the figure before you decide.
Does relining change how my chimney looks from outside?
Usually only the top changes, where the top plate and the liner cap sit above the crown. If a wall connection is involved, the tee opening is finished and sealed. We describe any visible change in the estimate before work starts.
More Ways to Care for Your Fireplace
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Chimney Crown RepairRepair the damaged chimney top with an approach matched to the crown and supporting masonry.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo