Chimney liner installation for fireplaces in Southwest Ranches
A listed liner, installed to its manual, with a written record of the work when the job is done.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Observations that start a relining assessment
- An inspection note about the flue lining
- A metal liner with no label
- Two appliances sharing one chimney
- A stale odor drifting from the flue
Jump to
A closer look at liner installation
Sizing starts with the appliance manual
A liner is sized to the appliance it serves, not to the opening at the top of the chimney. The DuraLiner instructions, for example, say the liner shall be no smaller than the size the appliance manufacturer specifies. Other listed systems carry similar wording in their own manuals.
That is why we ask for the make and model before we quote. With the appliance manual in hand, the required flue size becomes a documented figure rather than an estimate. If the manual is missing, we look for the model label on the unit and work from the published instructions.
When the appliance connects through the chimney wall
Some appliances connect to the chimney through a hole in its side rather than through the fireplace opening. For that arrangement the code calls for the inlet to enter from the side through a thimble, so the connector can neither slip out nor reach past the liner wall. Liner systems handle this connection with a tee fitting.
A tee usually includes a removable cap at its base for cleaning access. We look at the existing wall opening, the thimble and the connector route before choosing the fitting. If the opening needs work to accept the tee, that is described in the estimate as part of the connection.
Ask which requirement a relining line rests on
Every major line in a relining estimate should trace back to a requirement or a manual. The flue size comes from the appliance instructions. Insulation and clearances come from the liner listing. The need for a lining at all comes from the code's chimney chapter.
If any line in our estimate seems unexplained, ask where it comes from. We can point to the document behind it, whether a code section, a listing or a manual. That makes the proposal easier to check and easier to compare with others.
How the bottom of the liner is reached
The lower end of the liner is where most connection work happens. Access may be through the fireplace opening, through a wall thimble, or through a cleanout. Each route affects how the job is done and how long it takes.
We explain the access route in the estimate. If a panel, surround or damper must be removed, the proposal says how the area is reinstated. You approve that disturbance before the work begins, not after the fact. Tight access at the bottom can also affect which connector suits the job.
Checked and priced before relining in Southwest Ranches
- Top plate and clamp assembly
- Liner cap with its spark screen
- Debris cleaned up and hauled away
- Code label near the connector where required
Flue liner answers before you approve
Why does the estimate list cleaning separately from the liner?
Liner makers ask for the existing flue to be inspected and cleaned before relining, and the effort varies from chimney to chimney. Listing it separately shows you what the preparation involves and what it adds to the total.
How does the discount after the free inspection work?
When you book the relining no more than 72 hours after your free inspection, a 10% discount applies to the agreed work. The window starts from your own inspection, and the estimate shows the figure before you decide.
Can I use my fireplace while I decide about relining?
If an inspection has raised doubts about the lining, hold off until the question is resolved. A damaged lining can let heat and flue gases reach places they should not. We explain what is known so you can decide with the facts.
More Ways to Care for Your Fireplace
- Chimney Crown RepairRepair the damaged chimney top with an approach matched to the crown and supporting masonry.
- Hurricane and Storm Damage Chimney RepairAssess storm-related chimney concerns and distinguish temporary protection from permanent component repair.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo