Chimney liner installation for fireplaces in Virginia Gardens
Tell us what burns at the bottom of the flue, and we plan a liner that suits it.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Clues that a flue needs relining in Virginia Gardens
- Broken clay pieces in the fireplace
- A metal liner with no label
- A planned switch from gas to solid fuel
- Gaps between flue tiles seen from above
Jump to
Chimney relining details worth knowing in Virginia Gardens
Gas-fired appliances and the fuel gas chapter
When a gas-fired appliance vents into a masonry chimney, the Florida Fuel Gas Code chapter on chimneys and vents applies. It accepts clay lining, a lining system listed to the chimney liner standard, or other approved material. It also recognizes liners listed for gas service only, which carry their own labels.
Tell us the fuel and the appliance type before we plan the liner. A liner chosen for solid fuel is not automatically right for a gas-fired appliance, or the reverse. The appliance manual and the liner listing together decide it, and we show both in the proposal.
Removing a failed liner before replacement
Chimney liner replacement starts with taking the old liner out. Corroded or crushed pipe can resist removal, and parts may come out in sections. The existing top plate, cap and connector usually go with it.
We explain how the old liner will be removed and where the waste goes. Debris is cleaned up and hauled away at the end of the work. If the removal reveals damage to the flue behind it, we stop and discuss it before the scope changes. The replacement liner is then sized as if the job were new, from the appliance manual rather than the old pipe.
What stays hidden during a relining assessment
Parts of a flue cannot be seen from the top or the bottom, especially behind offsets. We describe the accessible sections and say which parts remain concealed. A proposal should not pretend to know the condition of a passage nobody could see.
Where concealed sections could change the job, the estimate names that risk in plain words. If opening the passage reveals something new, work pauses and we explain it. Nothing is added to the agreed scope until you approve it, and the price of any addition is stated first.
Factory-built chimneys are not relined the same way
A factory-built metal chimney is a listed assembly of its own. Its pipe, spacers and top parts come from one manufacturer and follow that listing. It is not a masonry chimney waiting for a liner.
If your fireplace uses a factory-built chimney, relining in the masonry sense does not apply. Damaged parts are replaced with the parts the maker specifies. We explain which kind of chimney you have at the start, so the right service handles it and the estimate describes the right work. The two kinds can look alike from the roof, so we check from below as well.
What our liner assessment covers
- Tee fitting for a wall connection
- Unused flue closure as a separate item
- Room protection at the fireplace opening
- Code label near the connector where required
Common questions about a new flue liner
What should I have ready for the free inspection?
The appliance make and model, its manual if you have it, and any earlier inspection wording about the lining. Old invoices for chimney work help too. If you cannot find these, we locate the model label during the visit.
Do you install liners for open fireplaces as well as appliances?
Yes. For an open masonry fireplace, the code sizes the flue against the fireplace opening, so the calculation differs from an appliance. We explain which rule set the size in the estimate, along with how the liner leaves the smoke chamber.
What if the liner will not fit down my flue?
Then the options are preparation, such as removing broken tile, or a different liner form that suits the route. If neither works, we explain what that means for the appliance. You hear this at the assessment, not on installation day.
More Ways to Care for Your Fireplace
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo