A chimney rebuild contractor for Coral Gables
Tell us what fell, what moved or what keeps failing, and we explain whether rebuilding fits.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What a chimney due for rebuilding shows
- Cracks running through several bricks
- Rust stains from failed metal ties
- A bulge in the chimney face
- A top section that sways in the wind
Jump to
From removal to new crown, a full rebuild
Looseness that runs down through the courses
A few loose bricks at the very top are a repair job. When bricks move by hand several courses down, and the mortar behind them crumbles when touched, the whole section has lost its bond.
Relaying individual units in that condition leaves them surrounded by masonry that is just as weak. We check how far down the looseness goes, course by course, where it is safe to do so. That depth sets the likely removal line for a partial rebuild, and the estimate names it.
Where the new masonry meets the old
The join between rebuilt courses and retained masonry is the most visible line on a partial rebuild. A clean, level transition with matching joint lines makes it read as one chimney.
We set the first new course carefully on the prepared old masonry and carry the joint lines through. Some difference in color is likely at first, since the old brick has weathered. We explain what to expect before you approve and how the contrast usually softens over time. Where the join falls at the roof line, the flashing often hides much of it anyway.
Metal chimneys are not rebuilt in brick
A factory-built chimney is a listed metal system, often inside a framed chase with siding or stucco. It is repaired or replaced with the parts its maker specifies, not rebuilt in masonry.
If your chimney turns out to be factory-built, we tell you on the visit. The framed chase and its cover have their own services, and the metal chimney itself follows its listing. A masonry rebuild applies only where the chimney is built of brick, block or stone. We look for the label or model details so the right parts can be identified.
Questions to ask before approving a rebuild
Ask where the removal will stop and how that line was chosen. Ask how the flue will be lined, what the crown will be made of and whether the new top meets the code's height rule.
Ask who handles the roof covering and flashing, how the house and yard will be protected and how changes are priced if removal uncovers more. Clear answers to those questions tell you whether a rebuild estimate has been thought through. We welcome those questions on the visit and answer them in writing on request.
How a chimney rebuild is itemized in Coral Gables
- Structural assessment flagged where needed
- Shoulders laid to shed water
- Curing time before the fireplace is lit
- Uncovered damage shown before the scope grows
Questions people raise about a rebuild in Coral Gables
How do you decide how far down to take the chimney?
We look for the point where the masonry becomes sound again: firm mortar, tight units and no cracks running below. The estimate names that level and explains the evidence, and we confirm it once removal reaches it.
Do you rebuild factory-built metal chimneys in brick?
No. A factory-built chimney is a listed system and is repaired with the parts its maker specifies. Rebuilding applies to masonry chimneys, and we tell you which kind you have on the visit.
Will a rebuild change how my fireplace draws?
It should not make it worse. The rebuilt flue is kept to a size that suits the fireplace, and the top follows the code's height rule. If draft was a problem before, we explain what the rebuild can and cannot change.
More Ways to Care for Your Fireplace
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Chimney Sweep and Chimney CleaningArrange careful chimney cleaning in Miami with a defined scope, protected work area and useful findings.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo