Chimney rebuilds and flue decisions in Little River
Where repairs keep failing, we explain whether rebuilding the section is the sounder choice.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Damage that points toward a rebuild
- A stack that has tipped out of plumb
- Broken brick spread over large areas
- Daylight through the masonry in the attic
- Brick falling onto the roof
Jump to
Chimney reconstruction explained before it starts
Checking flue tiles before they go in
A clay flue tile hidden inside new masonry cannot easily be inspected or replaced. The brick industry's guidance calls for inspecting flue tiles for cracks and other damage just before installation.
We check each tile as it arrives and again before it is set. A damaged tile is set aside rather than built in, and a replacement is ordered. It is a small step, but it protects the whole rebuild, since a cracked lining can let heat and exhaust reach the masonry and the house.
Saving sound bricks from the old stack
Original bricks from the dismantled section can often be reused. Each one is cleaned of old mortar and checked for cracks, broken faces and softness. Only sound units go back into the new work.
Reused brick helps the rebuilt section blend with the masonry below. It is more work than laying new brick, since each unit must be cleaned and checked, and the estimate reflects that. Where there are not enough sound units, we mix in new or salvaged brick and explain where they will sit.
When masonry repair will do
Not every damaged chimney needs rebuilding. Where the damage is limited to certain joints or units, and the stack has not moved, chimney masonry repair can fix it in place.
We explain which case you have. If the evidence points to a local repair, we price that instead of a rebuild. If you would like both options priced, we can set them side by side with the reasons for each, so you can compare scope and expected life. Choosing the smaller repair now does not rule out a rebuild later if the chimney needs it.
When only the top needs work
Sometimes the masonry is sound and the problem is the crown alone: cracks, a missing overhang or a flat mortar wash. In that case, chimney crown repair addresses the top without taking any brick down.
We check the top courses under the crown before suggesting a crown-only repair. If they are loose or soaked, the crown and the courses below may need to be handled together. The estimate explains which case applies. A crown repair is a far smaller job than a rebuild, so it is worth ruling in or out first. We tell you plainly which way the evidence points.
Chimney rebuild lines you approve
- Corrosion-resistant ties where the chimney needs them
- Tooled joints that shed water
- Sample panel for brick and mortar
- Flue size kept to suit the fireplace
Your chimney rebuild questions
Is a partial rebuild enough for my chimney?
Often, yes. Damage is usually worst above the roof, where the weather hits hardest. If the masonry below is sound, rebuilding only the damaged top section is the normal approach, and we explain why.
Is there a discount if I book the rebuild soon?
Yes. Once the free inspection at your home is done, you have 72 hours in which any service you book carries a 10% discount. The rebuild scope stays exactly as written either way.
Do you rebuild factory-built metal chimneys in brick?
No. A factory-built chimney is a listed system and is repaired with the parts its maker specifies. Rebuilding applies to masonry chimneys, and we tell you which kind you have on the visit.
More Ways to Care for Your Fireplace
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
- Hurricane and Storm Damage Chimney RepairAssess storm-related chimney concerns and distinguish temporary protection from permanent component repair.
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo