Chimney mortar joints repointed in Hialeah Gardens
We match color, texture and profile, and explain how new mortar weathers in.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs the chimney joints need repointing
- Joints that crumble when scraped
- Stepped cracks following the mortar lines
- Caulk pushed into open joints
- Water inside after rain on one side
Jump to
Joint repair that protects the brick
Raking chimney joints to an even, sound depth
Old mortar is removed to an even depth before any new mortar goes in. Brick industry guidance ties that depth to the width of the joint, or deeper where the mortar is still unsound. An even depth lets the new mortar bond and cure consistently.
Uneven raking leaves thick new mortar in some spots and a thin skin in others. The thin areas are the ones most likely to crack and pop out later. We rake each joint to sound material and check depth as we go, so the repair has a proper base throughout.
A clean, square cut behind each joint
How a joint is cut out matters as much as how deep it goes. Federal preservation guidance asks for old mortar to come away cleanly, with the back of each cut left square rather than rounded. A rounded or V-shaped cavity gives new mortar less to grip.
We clear each joint so the new mortar meets clean brick surfaces on both sides. That is slower than running a tool down the middle of the joint. It is also what lets the repointed mortar lock into place instead of sitting in a shallow groove.
How tooling time changes the joint color
Timing affects appearance as well as performance. Brick industry guidance notes that joints tooled early tend to dry lighter and joints tooled late tend to dry darker. Federal preservation guidance describes dark streaks when mortar is tooled too hard.
On a chimney face repointed in sections, those differences show as bands. We pace the work so each section reaches the same stage before tooling. If the weather changes during the day, we adjust the pace rather than tool mortar that is not ready.
Comparing chimney tuckpointing estimates
Two repointing quotes can describe very different work. One may involve raking every failed joint to proper depth and matching the mortar. Another may be a thin skim over the old joints. The numbers only compare fairly once you know which is which.
Put the same questions to everyone who quotes. Ask how deep the joints will be raked, how head joints are cleared, which mortar is used and how the color is matched. Our proposal sets those answers down on paper, so a side-by-side comparison is straightforward.
Separate lines for joints and bricks
- Removal of mortar slivers on brick edges
- Joint profile that sheds water
- Curing care for the new joints
- Workmanship warranty on the agreed joints
Tuckpointing questions from homes in Hialeah Gardens
Do you match the new mortar to the brick or the old mortar?
Both matter. The mortar should suit the brick, which means softer and more permeable than the units and no harder than the original mix. Its color and texture are matched to the existing joints so the repair blends in.
What should I do to prepare for tuckpointing at my home?
Clear access to the chimney base, move vehicles away from that side of the house and keep pets indoors. Tell us about plants, vents or fragile roofing near the chimney. We handle protection and cleanup.
Will you repoint the joints inside my firebox as well?
Firebox joints use refractory mortar and belong to firebox repair, a separate service. Chimney tuckpointing covers the exterior masonry. If both need work, each is priced on its own line so you can decide.
More Ways to Care for Your Fireplace
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Chimney Cap Installation and ReplacementProtect the chimney opening with a cap chosen for its fit, attachment and compatible system.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo