Mortar joint repair for brick chimneys in Westview
Joint repairs planned to protect the brick faces, backed by our workmanship warranty on the agreed work.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Chimney mortar damage worth a closer look
- Mortar eroded back from the brick face
- Joints on one face far worse than others
- Stepped cracks following the mortar lines
- Thin mortar smeared over old joints
Jump to
Choosing mortar for a chimney repoint
Raking chimney joints to an even, sound depth
Old mortar is removed to an even depth before any new mortar goes in. Brick industry guidance ties that depth to the width of the joint, or deeper where the mortar is still unsound. An even depth lets the new mortar bond and cure consistently.
Uneven raking leaves thick new mortar in some spots and a thin skin in others. The thin areas are the ones most likely to crack and pop out later. We rake each joint to sound material and check depth as we go, so the repair has a proper base throughout.
Repointing out of direct sun on hot days
Mortar needs time to cure with water in it. Federal preservation guidance recommends doing repointing work in the shade where possible, because strong sunlight on a hot wall pulls water out of fresh joints before they bond.
We plan the work so the face being repointed is in shade where possible, and we cover it when it is not. That can mean starting on a different face in the morning and another in the afternoon. We explain the plan so the sequence makes sense to you.
Recurring white deposits and hidden water
White deposits on brick are left behind as water dries out of the masonry and carries soluble salts to the surface. The maintenance guidance from the brick industry says deposits that keep returning deserve scrutiny, because they point to water that is still getting in.
We treat recurring deposits as a sign to look for the water source before repointing. Failed joints can be part of the path, but so can the crown, the cap or the flashing. Repointing is planned once the likely source is understood, so the new joints are not soaked the same way.
What changes the size of a repointing job
Repointing jobs vary a great deal. How many faces are involved and how deep the failure runs both change the work. So do the hardness of the old mortar and what it takes to reach the stack above the roof. A sample area adds a step too.
We tell you which of these shape your job. Each area is priced upfront on the estimate. Should the work grow once raking begins, it stops at that point and we talk it through with you before anything extra goes ahead.
Before you approve tuckpointing in Westview
- Head joints cleared by hand
- Removal of mortar slivers on brick edges
- Pre-hydrated mortar placed in thin layers
- Tooling at thumbprint hardness
Answers about chimney repointing
Can you repoint only the worst joints on the chimney?
Sometimes. Where damage is confined, spot repointing can be sensible. Brick industry guidance also suggests repointing every joint in an affected area, because it is hard to tell which joints admit water. We explain the boundary we recommend.
Does the workmanship warranty cover tuckpointing in Westview?
Yes. The joints we renew under the agreed scope carry our workmanship warranty. The written record lists the faces and areas repointed, which helps if you notice anything about the chimney later on.
Why did earlier repointing fall out of the joints?
Shallow preparation is a frequent reason. When old mortar is not raked deep enough, a thin skin of new mortar has little to grip. A mix that is too hard, or water still entering the wall, can also cause it.
More Ways to Care for Your Fireplace
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Hurricane and Storm Damage Chimney RepairAssess storm-related chimney concerns and distinguish temporary protection from permanent component repair.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
- Fireplace RestorationCoordinate fireplace repairs while preserving suitable existing features and defining the intended use.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo