Wood insert installation with a full-length liner, Boca Raton
At handover you get the manual, the serial number on record and a clear walk-through of the air control.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What leads to a fireplace insert installation in Boca Raton
- An old insert with no full liner
- Smoke puffing from an existing insert
- A faceplate that no longer seals
- A loose or missing liner cap
Jump to
Insert, liner and hearth, planned together in Boca Raton
Clearances to side walls, facing and trim
Every insert label lists minimum clearances to combustible materials around it, such as side walls, the top facing and trim beside the opening. Those distances are measured from the unit, not from the old fireplace opening. Wood paneling or trim that was fine beside an open fireplace may now be too close.
We measure the combustible materials around your fireplace against the label of each insert you are considering. Where trim is too close, we explain whether it can be moved or replaced with noncombustible material. That work is a separate item, and it happens before the insert is installed.
Replacement parts from the insert's parts list
Manuals say that if a component fails, it should be replaced only with the maker's listed part. Baffles, air tubes, firebrick, gaskets and glass are all specific to the model. A generic substitute may fit loosely or behave differently under heat.
Your written record names the model and serial number, which makes ordering the right part straightforward. We explain which parts wear with normal use and which should last much longer. Replacing a worn part early is usually simpler than waiting for it to fail.
Handover and the first walk-through
At handover, we go through the air control, the door latch, the blower if fitted and the loading routine the manual describes. We point out the label, the clearances and the floor protection so you know where they are. The manual stays with you.
We also explain the break-in fires, the paint odor and the habits the manual asks for, such as keeping the door closed and the ashes in a metal container. Questions that come up after the early fires are welcome, and a maintenance visit can follow later.
When the opening is too small
Some fireplace openings are simply smaller than the minimum an insert manual lists. Cutting the masonry to enlarge the opening is not an option the manuals allow. The choice then lies between a smaller model, a different appliance or leaving the fireplace as it is.
We check the smallest suitable models before telling you an insert will not fit. If none fits, we say so plainly and explain what else is realistic. You are not left with a unit that cannot be installed, and the inspection costs you nothing.
Parts of the insert job the estimate separates
- Liner insulation where instructions require
- Appliance connector and high-temperature sealant
- Baffles and smoke deflector in place
- Written record of the insert installation
Fireplace insert questions we hear in Boca Raton
Can the insert connect to my home's air conditioning ducts?
No. Insert manuals warn against connecting to any air distribution ductwork unless the manual approves it specifically. The insert heats the room it sits in, and its flue gases go only up the liner.
Is the chimney cleaned before the liner is installed?
Yes. Insert and liner instructions call for the chimney to be cleaned and checked first. We do that as a separate step, look for damaged masonry and explain any repair before relining continues.
Can an insert go into a fireplace with cracked firebrick?
Not until the firebrick is repaired. Insert manuals require a sound host free of cracks and loose mortar. The repair is a separate item handled by our firebox repair service before the insert is installed.
More Ways to Care for Your Fireplace
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Ventless Gas Fireplace ServiceService the identified vent-free appliance without bypassing its required safety components.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
- Chimney Crown RepairRepair the damaged chimney top with an approach matched to the crown and supporting masonry.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo