A new wood-burning fireplace, installed in Brickell Key
Factory-built or masonry, the choice follows your room, the structure and the chimney path, not a showroom photo.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What starts a fireplace installation project in Brickell Key
- A prefab unit with a warped firebox
- Rusted metal inside an old fireplace
- A masonry fireplace you want built new
- An enclosure too small for newer units
Jump to
From listing label to first fire, the installation
Mantel height and depth follow the manual
If you plan a mantel above the opening, its height and projection are set by the unit's manual, not by taste alone. Deeper mantels generally have to sit higher. A combustible shelf placed too low can overheat, even when the fire looks well contained.
We mark the lowest allowed mantel position on the framing before the wall is finished. The mantel itself is not part of our work, so share the marked height with whoever supplies it. The mark saves an expensive correction once the stone or tile is set.
Ask what review the installation needs
Fireplace manuals tell owners to contact the local building or fire officials about restrictions and installation inspections before work begins. The requirements depend on the job and the jurisdiction, and we do not assume every installation is treated the same way.
Ask us early what review your project may need and how it fits the schedule. If an inspection is required at a rough-in stage, the walls stay open until it happens. We explain those steps rather than promising a shortcut around them.
Starting fires without flammable liquids
Manuals warn against using gasoline, lantern fuel, kerosene or charcoal lighter fluid to start or freshen a wood fire. Those liquids can flash and overfire the unit. Paper, dry kindling and a pre-warmed flue do the job safely.
We show you the lighting method your manual describes, including how to warm the flue so smoke rises from the start. Keep flammable liquids and their vapors stored well away from the fireplace room. A calm start makes for a clean fire and a cleaner chimney.
What the installation includes and leaves out
A typical wood fireplace installation from us includes planning, framing the enclosure, setting the unit, the listed chimney and roof parts, the hearth extension, outside air and handover. A masonry build adds the footing, firebox, smoke chamber and flue. The estimate states exactly which of these apply.
Left out, unless the estimate names them, are electrical circuits, roofing beyond the penetration, the finish face, the mantel and painting. Those boundaries are written so nothing falls between trades. Ask about any item you expected to see.
The fireplace installation scope, item by item
- Floor, ceiling and attic framing check
- Chimney route from firebox to roof
- Hearth extension size and material
- Debris cleanup and haul-away
Asked before a fireplace installation in Brickell Key
Why does my new fireplace need an outside air supply?
The Florida Building Code asks for exterior air to fireplaces unless the room is mechanically ventilated and kept at neutral or positive pressure. For a factory-built unit, the air parts must be listed components. We plan the intake with the chimney route.
Could you install a gas or electric fireplace instead?
Those are separate services with their own rules and parts. This installation service covers wood-burning fireplaces. Tell us which fuel you prefer when you call, and we arrange the right visit and scope for it.
Can a masonry fireplace be built on an upper floor?
It is rarely practical, because the code requires a concrete or solid masonry footing beneath the fireplace and chimney. A factory-built unit is framed into the floor structure instead. We explain the options that suit your house.
More Ways to Care for Your Fireplace
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
- Chimney Crown RepairRepair the damaged chimney top with an approach matched to the crown and supporting masonry.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo