New vented gas fireplaces installed in Belle Meade
Choose the appliance with its vent route and room in view, not from a picture alone.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Projects that start with a gas fireplace plan
- An existing vent of unknown make
- Several trades working on one room
- A particular look chosen for the wall
- A new deck crowding the old termination
Jump to
Building a gas fireplace around its manual
Straps and supports along the new vent
Vent sections need support so their weight does not rest on the appliance or on joints. Vent makers supply wall straps, support plates and firestop supports for this, and the fuel gas code requires vents to be supported as the vent manufacturer instructs.
We place supports as the vent instructions show and at every change of direction where they are called for. Long vertical runs and runs through attics get particular attention. A well-supported vent keeps its joints engaged over time, which protects the seal between sections.
Placing logs, embers or media to the diagram
Gas fireplaces come with logs, embers, glass media or stones that are part of the listed appliance. The manual shows exactly where each piece goes, because the placement shapes the flames and keeps them from touching surfaces that would soot.
We place the media to the diagram and keep extra material out of the unit, even if it would look fuller. The first fires are watched for flame contact and adjusted to the diagram if needed. Keep the diagram with the manual so the layout can be restored after future service.
The written record of the installation
At the end of the job you receive a written record of the work. It lists the appliance model and serial number, the fuel, the vent system and route, the restrictor setting, the pressure readings, the checks completed and anything left for another trade.
That record matters most for the parts that disappear behind the finish, such as clearances inside the wall, firestops and joints. Keep it with the manuals. When the unit is serviced in later seasons, the record tells the next person what was installed and how.
Reusing an existing chase or enclosure
An existing chase or built-in enclosure can sometimes take a new gas fireplace, but its framing sizes, clearances, blocking and insulation must suit the new model. A chase built for one unit is not automatically right for another.
We compare the existing enclosure with the new manual during the project inspection. If changes are needed, they are listed and priced. If the enclosure cannot be adapted safely, we say so and explain what rebuilding it would involve, so you can decide before ordering.
What your gas fireplace installation estimate covers
- Control and service access planned
- Vent assembled with every joint locked
- Pressure readings and operating check
- Walkthrough and manuals handed over
Questions from Belle Meade about new gas fireplaces
Do I need an electrician for a gas fireplace installation?
Often, because many models need household power for ignition, a blower or lighting. The manual states the requirement. If a new circuit is needed, an electrician installs it, and we coordinate the timing with the appliance work.
Do you keep the manual on site for a code inspection?
Yes. The Florida fuel gas code expects the installation instructions to be available on the job site when the installation is inspected. We keep them with the unit during the work and hand them to you at the end.
Can a gas fireplace be added to a room with no fireplace?
Often, if a permitted vent route and a suitable framed enclosure can be created. The project inspection tells you whether your chosen position works and what construction it needs before anything is ordered.
More Ways to Care for Your Fireplace
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
- Fireplace RestorationCoordinate fireplace repairs while preserving suitable existing features and defining the intended use.
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo