New vented gas fireplaces installed in Biscayne Island
The installation follows the listing and manual for the unit you choose, from framing to handover.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Gas fireplace projects we are asked about
- An old gas unit you want replaced
- Parts no longer made for the existing unit
- A builder asking for framing details
- A particular look chosen for the wall
Jump to
The parts of a gas fireplace project
Keeping insulation away from the unit and vent
Loose insulation, debris and stored items can end up against a fireplace or its vent if the enclosure is not blocked properly. One manual requires the chase to be blocked so that blown insulation and other combustibles cannot reach the fireplace or chimney.
We look at how insulation will be installed around the enclosure and where blocking is needed. Attic spaces get particular attention, because insulation is often added later by someone who does not know the vent is there. Where the manual supplies a shield for that job, it is fitted and recorded.
Manuals that stay with the house
Installers are asked to leave the manual with the person responsible for the appliance. It holds the model details, the media diagram, the maintenance list and the parts list, all of which future service depends on.
We hand over the installation and owner's manuals with the vent instructions and any accessory manuals. Keep them together near the fireplace or with your house papers. If you sell the house, pass them on. A gas fireplace with its manuals is far easier to service than one without them.
Termination parts where salt air reaches
Close to the coast, exterior metal faces chlorides carried from sea spray, which galvanizing research links to faster corrosion of zinc coatings. A vent termination and its exterior pipe sit in that air every day.
Where a vent maker offers termination caps or exterior parts in stainless steel or other finishes for your system, we explain the options during planning. Only parts listed for the vent system are used. The finish chosen and the exposure of the wall are noted, so future service knows what to watch.
Mixed metals at the termination
Where two different metals touch in a corrosive setting such as salt air, one of them can corrode faster than it would alone. Galvanizing guidance notes this for galvanized steel in contact with metals such as stainless steel, aluminum and copper.
At the termination, we use the fasteners and brackets the vent maker lists and avoid mixing metals the instructions do not call for. Flashing and trim near the cap are checked for contact with the vent parts. The materials used are recorded for future service.
Line items for a new gas fireplace
- Supply handover point agreed with the gas contractor
- Electrical requirement noted for an electrician
- Wall or roof penetration sealed
- Finish work boundaries shown on the estimate
Gas fireplace project questions we hear
Can the fireplace go on an interior wall?
Sometimes. The vent route has to reach a permitted termination within the vent tables for the model. Longer routes and extra elbows can rule some positions out, so we check the route before you commit to that wall.
Do you keep the manual on site for a code inspection?
Yes. The Florida fuel gas code expects the installation instructions to be available on the job site when the installation is inspected. We keep them with the unit during the work and hand them to you at the end.
What if the wall I want has no room for the vent route?
We look for another route or another position that fits the vent tables and termination rules. If no permitted route exists for that wall, we say so plainly and suggest positions that do work.
More Ways to Care for Your Fireplace
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
- Fireplace RestorationCoordinate fireplace repairs while preserving suitable existing features and defining the intended use.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo