A new gas fireplace in Coconut Creek, installed to its manual
We explain what the installation includes, what another trade handles and what is priced separately.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs it may be time for a new gas unit
- Rust holes in the old firebox
- A renovation opening up the wall
- A unit bought before the route was checked
- A particular look chosen for the wall
Jump to
The parts of a gas fireplace project
Combustion air for units that use room air
A natural-draft gas fireplace burns air from the room it sits in. The fuel gas code sets methods for providing enough combustion, ventilation and dilution air, either from inside the building or brought in from outdoors. Direct-vent units follow their manuals instead, because they draw air from outside.
For natural-draft models, we look at the room and the connected spaces during the project inspection. If the room does not meet the code's indoor air method, outdoor air may be needed. We explain what that means for your plan before the model is ordered.
Horizontal terminations and moisture
A horizontal termination sits on an outside wall. One manual asks for the termination cap to slant slightly downward so moisture in the cap can drain out. The same manual allows horizontal runs to be level rather than rising.
We set the termination and the last section of the run to the manual's instructions. The cap is fastened to the wall as shown, sealed where the manual calls for it and checked for the clearances it needs outside. A cap mounted the wrong way can hold water against the wall and the vent.
The appliance shutoff valve location
Every gas appliance needs a shutoff valve. Under the fuel gas code, that valve normally sits in the same room with access. Vented decorative appliances may instead use a remote valve with ready access, permanently identified. Some fireplaces also locate a valve inside the unit as the manual shows.
The valve is part of the supply work, installed by the gas contractor or arranged with the utility. We agree its position with them so it suits the appliance connection and stays accessible after the finish goes on. The position is written on the installation record.
The gas contractor's part of the project
Supply piping to a new gas fireplace is installed by a gas contractor, or arranged with the gas utility where they provide it. Their work covers sizing and running the supply, testing it and fitting the shutoff valve. We do not install supply piping.
We give the gas contractor the appliance position, the connection point and the input shown in the manual. Their work usually happens during rough-in, before walls close. Once the supply is ready and tested, we set and connect the appliance as the manual shows and carry out the leak and pressure checks at the unit.
Appliance, vent and framing items for your gas unit
- Room and appliance position review
- Attic insulation shield where the route needs one
- Control and service access planned
- Finish work boundaries shown on the estimate
Before you plan a gas fireplace
What happens on the day the new fireplace is lit?
We check the appliance connection for leaks, take pressure readings, light the unit and watch it through its sequence. Then we show you the controls, the barrier and the maintenance list in the manual.
What does the free project inspection cover?
We look at the room, the intended position, possible vent routes, the framing and access, and the fuel supply situation. You then receive a written scope that separates our work from the work of other trades.
Should the fireplace go in before or after the finish work?
The appliance, framing and vent come first, and the finish follows to the manual's requirements. Some models allow certain finish materials only in set zones. We agree the sequence with your builder so nothing has to be undone.
More Ways to Care for Your Fireplace
- Hurricane and Storm Damage Chimney RepairAssess storm-related chimney concerns and distinguish temporary protection from permanent component repair.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo