Built-in gas fireplace installation in Durrs
We install the appliance you approve, test it, and show you how it should run.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Reasons to plan a gas fireplace in Durrs
- An old gas unit you want replaced
- Parts no longer made for the existing unit
- Wanting a fire without burning wood
- Cabinetry planned around the fireplace
Jump to
Gas appliance, vent and enclosure as one plan
Supply pressure tests and the appliance
When supply piping is pressure tested, the appliance must be protected. One manual requires the appliance and its valve to be disconnected from the supply during tests above a set pressure, or isolated by closing its shutoff valve during lower-pressure tests.
We agree the order of work with the gas contractor, so their test happens before the appliance is connected, or with the appliance isolated as the manual requires. That avoids damage to the appliance valve before the fireplace has ever been lit. The sequence is noted on the record.
Ceiling height and the space above the unit
Manuals set minimum distances from the appliance to the ceiling and to anything combustible above it. Low ceilings, soffits and beams near the fireplace position can limit which models fit or where the unit can sit on the wall.
We measure the space above the planned position during the project inspection. If a raised installation is part of the design, we check that the ceiling clearances still work at that height. Those checks happen before framing, when changing the height is still simple.
Plants and landscaping near the termination
Shrubs, vines and trees can grow toward a wall termination, and leaves and debris can collect around it. One owner's manual lists plants, nests, leaves and debris among the things to check at the termination.
When choosing the exit point, we look at the planting around it and mention what will need trimming over time. After installation, keep growth clear of the termination as the manual describes. If landscaping plans are underway, share them so the termination and the garden do not end up competing for the same space.
Reaching the termination for future checks
A termination that is hard to reach is easy to forget. Manuals ask owners and service people to check terminations for blockage, damage and clearance, which is simpler when the cap can be seen and reached safely.
We consider access when choosing the exit point, especially for roof and high wall terminations. The location is noted on your installation record, so a future visit knows where to look. If a less visible position is chosen for appearance, we explain what that means for later checks.
The installation checklist for your gas unit
- Fuel type matched to the house supply
- Termination position against listed clearances
- Wall and ceiling firestops where required
- Pressure readings and operating check
Gas fireplace installs, questions answered
Can the new vent run through a closet or storage space?
It can, where the route allows. The vent is enclosed and the enclosure blocked as the manual describes, so stored items and insulation cannot reach the pipe. We explain what should be kept clear of that enclosure once the job is finished.
Can a gas fireplace go in a bedroom?
The fuel gas code limits gas appliances in bedrooms and bathrooms, with exceptions that include direct-vent units installed to their listing and manual. Whether your model qualifies depends on its listing, so we check that before planning the location.
How do you handle framing and finishes around the unit?
We follow the framing and clearance drawings in the manual for the chosen model. Where a builder or another trade frames the chase or applies the finish, we share those requirements with them before they start.
More Ways to Care for Your Fireplace
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Stone Chimney RepairRepair affected stone chimney surfaces with the supporting construction and visual match considered together.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo