Gas fireplace installer serving Harbour Inlet
The installation follows the listing and manual for the unit you choose, from framing to handover.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When a gas fireplace installation makes sense
- Rust holes in the old firebox
- Propane supply but no appliance yet
- An existing vent of unknown make
- Several trades working on one room
Jump to
Planning a gas fireplace installation step by step
Decorative caps and shrouds must be listed
You may want a decorative cover over a roof or wall termination. The manuals allow only listed decorative caps and shrouds used with the approved vent system, and one warns that a decorative cover can change the clearances the cap needs.
If you want a decorative cap, we choose it from the list for your vent system and check its clearances before ordering. A shroud made on site or taken from another product is not used. The chosen cap is recorded with the vent parts, so future service knows what is fitted.
Placing logs, embers or media to the diagram
Gas fireplaces come with logs, embers, glass media or stones that are part of the listed appliance. The manual shows exactly where each piece goes, because the placement shapes the flames and keeps them from touching surfaces that would soot.
We place the media to the diagram and keep extra material out of the unit, even if it would look fuller. The first fires are watched for flame contact and adjusted to the diagram if needed. Keep the diagram with the manual so the layout can be restored after future service.
Manuals that stay with the house
Installers are asked to leave the manual with the person responsible for the appliance. It holds the model details, the media diagram, the maintenance list and the parts list, all of which future service depends on.
We hand over the installation and owner's manuals with the vent instructions and any accessory manuals. Keep them together near the fireplace or with your house papers. If you sell the house, pass them on. A gas fireplace with its manuals is far easier to service than one without them.
Reaching the termination for future checks
A termination that is hard to reach is easy to forget. Manuals ask owners and service people to check terminations for blockage, damage and clearance, which is simpler when the cap can be seen and reached safely.
We consider access when choosing the exit point, especially for roof and high wall terminations. The location is noted on your installation record, so a future visit knows where to look. If a less visible position is chosen for appearance, we explain what that means for later checks.
Appliance, vent and framing items for your gas unit
- Termination position against listed clearances
- Control and service access planned
- Wall or roof penetration sealed
- Existing unit and vent assessed for replacements
Questions from Harbour Inlet about new gas fireplaces
Can a gas fireplace go in a bedroom?
The fuel gas code limits gas appliances in bedrooms and bathrooms, with exceptions that include direct-vent units installed to their listing and manual. Whether your model qualifies depends on its listing, so we check that before planning the location.
Can you replace my old gas fireplace with a new model?
Yes, as a planned installation. The new model's requirements are checked against the existing framing, vent and supply. Old vent parts stay only where the new manual lists them for that appliance.
Is the installation covered by a warranty?
Our workmanship warranty covers the installation work we carry out. The appliance and vent parts carry their manufacturers' own warranties. We explain both on the estimate so you know which covers what.
More Ways to Care for Your Fireplace
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney Crown RepairRepair the damaged chimney top with an approach matched to the crown and supporting masonry.
- Chimney Cap Installation and ReplacementProtect the chimney opening with a cap chosen for its fit, attachment and compatible system.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo