Built-in gas fireplace installation in Kendall
Upfront pricing for the appliance work, with supply, electrical and finish work shown on separate lines.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Gas fireplace projects we are asked about
- Parts no longer made for the existing unit
- An existing vent of unknown make
- A unit bought before the route was checked
- A new deck crowding the old termination
Jump to
What a gas fireplace installation involves
Vent parts from one listed system
Direct-vent systems are tested as complete assemblies with their own pipe, elbows, joints and terminations. The manuals warn against mixing pipe, fittings or joining methods from different manufacturers, even when sizes appear to match.
We order every vent part from the system the manual lists for your model, including firestops, shields and the termination. If a part is unavailable, we wait for the listed part or choose another listed system, rather than filling the gap with a similar-looking piece. The parts list goes into your written record.
Service access designed into the finish
The fuel gas code requires appliances and controls to be accessible for inspection, service, repair and replacement. For a vented gas fireplace, any panel or grille that comes off during routine servicing has to stay free of the building structure.
We plan the finish so the control area, access panels and any junction box stay reachable. That affects surround designs, built-in cabinets and removable fronts. A finish that looks complete but hides the controls creates a problem at the first service visit, so we settle access before the finish is designed.
Straps and supports along the new vent
Vent sections need support so their weight does not rest on the appliance or on joints. Vent makers supply wall straps, support plates and firestop supports for this, and the fuel gas code requires vents to be supported as the vent manufacturer instructs.
We place supports as the vent instructions show and at every change of direction where they are called for. Long vertical runs and runs through attics get particular attention. A well-supported vent keeps its joints engaged over time, which protects the seal between sections.
Protecting the house during installation
A gas fireplace project can involve work inside the room, in the attic and on the roof or outside wall. We cover floors, protect finished surfaces near the opening and take care on the roof covering where a vertical route is used.
Tell us about any delicate finishes, pets or access limits before the work begins. The appliance itself is protected during the finish stage, so dust and debris do not reach the burner or controls. We check those areas again before the unit is lit.
Items in a gas fireplace installation
- Wall and ceiling firestops where required
- Leak check at the appliance connection
- Pressure readings and operating check
- Existing unit and vent assessed for replacements
Before you plan a gas fireplace
Does a direct-vent unit need a chimney?
No. A direct-vent gas fireplace uses a sealed vent system that draws outside air and exhausts through a listed termination on a wall or roof. The route and termination must fit the manual's rules for that model.
Is the installation covered by a warranty?
Our workmanship warranty covers the installation work we carry out. The appliance and vent parts carry their manufacturers' own warranties. We explain both on the estimate so you know which covers what.
Can a gas fireplace be added to a room with no fireplace?
Often, if a permitted vent route and a suitable framed enclosure can be created. The project inspection tells you whether your chosen position works and what construction it needs before anything is ordered.
More Ways to Care for Your Fireplace
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo