Built-in gas fireplace installation in Poinciana Park
A replacement gas fireplace gets the same planning as a new one, including the retained vent and framing.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs it may be time for a new gas unit
- Parts no longer made for the existing unit
- A unit bought before the route was checked
- A particular look chosen for the wall
- Moving the fireplace to a different wall
Jump to
What a gas fireplace installation involves
Termination clearances from openings
The fuel gas code and the appliance manuals set clearances between a vent termination and nearby features. These include openable windows and doors, soffits and overhangs, inside corners, meters and regulators, and air intakes. The figures differ between direct-vent and other terminals.
We measure the planned termination against the manual for your model and mark it before the wall is opened. Where two sources differ, the stricter one applies. If a clearance cannot be met, the termination or the fireplace moves, rather than the rule being bent.
The appliance shutoff valve location
Every gas appliance needs a shutoff valve. Under the fuel gas code, that valve normally sits in the same room with access. Vented decorative appliances may instead use a remote valve with ready access, permanently identified. Some fireplaces also locate a valve inside the unit as the manual shows.
The valve is part of the supply work, installed by the gas contractor or arranged with the utility. We agree its position with them so it suits the appliance connection and stays accessible after the finish goes on. The position is written on the installation record.
If the chosen model changes
Sometimes a model is discontinued, delayed or replaced by a newer version after the plan is approved. A different model can have different framing sizes, clearances, vent tables and controls, even when it looks similar.
If the model changes, we review the plan against the new manual before anything else happens. You see what changes and what it means for the price. Nothing is built around a new unit until that review is done and you have approved the revised plan in writing.
Dust, debris and cleanup during the work
Installation involves cutting framing, opening walls or ceilings and handling packaging. We protect floors and furniture near the work area and control dust where cutting takes place.
Offcuts, packaging and old materials are removed as the job progresses. At the end, we clean up the debris and haul it away, leaving the room ready for the finish trade or for use. If other trades are working in the same room, we agree who clears what, so nothing is left behind.
Gas fireplace work and separate trade items
- Clearances to combustibles marked out
- Shutoff valve position coordinated
- Walkthrough and manuals handed over
- Finish work boundaries shown on the estimate
What people ask about new gas fireplaces
Where can the vent termination go on an outside wall?
Only where the manual's clearance rules allow it, measured from openable windows and doors, soffits, corners, meters, decks and walkways. We mark the position during the project inspection, before any opening is cut.
Do you keep the manual on site for a code inspection?
Yes. The Florida fuel gas code expects the installation instructions to be available on the job site when the installation is inspected. We keep them with the unit during the work and hand them to you at the end.
What does the free project inspection cover?
We look at the room, the intended position, possible vent routes, the framing and access, and the fuel supply situation. You then receive a written scope that separates our work from the work of other trades.
More Ways to Care for Your Fireplace
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
- Chimney Cap Installation and ReplacementProtect the chimney opening with a cap chosen for its fit, attachment and compatible system.
- Hurricane and Storm Damage Chimney RepairAssess storm-related chimney concerns and distinguish temporary protection from permanent component repair.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo