Direct vent fireplace repair for Lighthouse Point homes
A written scope separates vent repair from any appliance fault we find along the way.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs a gas fireplace vent needs attention
- Visible gap at a pipe joint
- Rust on exposed vent pipe
- Ceiling stain near a vertical vent
- Cap loose or missing after strong wind
Jump to
Gas fireplace venting work in Lighthouse Point
Parts from one maker's system only
Direct-vent pipe from different manufacturers can look alike, but joints, gaskets and locking methods differ. Appliance manuals prohibit mixing pipe, fittings or joining methods from different makers, even where the sizes seem to match.
When a section needs replacing, we order it from the same listed system, or from another system the appliance manual approves if the original is no longer available. We do not join two systems together with an adapter the manuals do not list. The parts used are written on your record.
B-vent installation from appliance to roof
A new Type B vent runs from the appliance draft hood or collar up to a listed cap above the roof. Along the way it needs firestop spacers at ceilings, an attic insulation shield where it crosses insulation, supports, roof flashing and a sealed storm collar.
We size and lay out the route to the appliance manual and the fuel gas code, using parts from one listed Type B system. The height above the roof follows the code's rules for the roof and nearby walls. Each stage is checked before ceilings and roof are closed up.
What we can see and what stays concealed
Much of a gas fireplace vent runs inside walls, ceilings and chases, where it cannot be seen without opening a finish. An assessment covers the accessible parts, and it says plainly which sections were not seen.
We do not describe a concealed section as sound when we could not see it. If the symptoms point to a hidden section, we explain where access would be needed and what it would involve. You decide whether to open it, with the access and restoration priced before any surface is cut.
A vent route review before walls close
Another installer or a builder may be fitting your gas fireplace vent. If you want it checked before the walls close, we can review the route against the appliance manual, the vent instructions and the code's clearance table.
We look at the parts, the route against the vent tables, the supports, the firestops and the termination position. Findings are written up so the installer can act on them. We do not take over someone else's installation without agreement, but a review at rough-in costs far less than opening a finished wall.
Gas vent work and separate access items
- Vent maker and system read from labels
- Attic insulation shield position
- Restrictor setting against the route
- Separate vent confirmed for the appliance
Before you book gas vent work
Do you check the vent connector on natural-draft units?
Yes. The connector joins a natural-draft appliance to its vent, and the fuel gas code requires noncombustible, corrosion-resistant material able to handle the vent gas temperature. We check its material, joints, slope, support and clearance, and quote a replacement where it fails.
Do you need to open the wall to repair a vent?
Sometimes. The manuals do not require inspection openings at joints inside walls, so concealed sections may need an access opening. We explain the access needed, and the wall restoration is listed as its own item before you approve.
What is a draft check on a natural-draft fireplace?
After warm-up, a test at the draft hood relief opening shows which way the exhaust is moving, up the vent or back out into the room. We carry it out during vent work on draft-hood appliances.
More Ways to Care for Your Fireplace
- Chimney Crown RepairRepair the damaged chimney top with an approach matched to the crown and supporting masonry.
- Stone Chimney RepairRepair affected stone chimney surfaces with the supporting construction and visual match considered together.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo