Gas fireplace vent repair and replacement in Palm Springs North
Our family team handles gas fireplace vent repair in Palm Springs North with clear pricing and no hidden fees.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What a failing gas vent can look like
- A new deck built close to the vent
- Rust on exposed vent pipe
- Water marks around the wall penetration
- Fire behaves oddly when fans run
Jump to
Vent work for gas fireplaces in Palm Springs North
The appliance manual sets the vent rules
For direct-vent appliances, the fuel gas code points to the manufacturer's instructions for venting and to its own table for wall termination clearances. For gas vents in general, it requires installation to the vent maker's instructions and sizing to the appliance manual.
That makes the manuals the working documents for vent repair. We bring the appliance and vent instructions for your system to the job, or find them from the labels. Where the manual and the code both set a rule, the stricter one applies.
B-vent installation from appliance to roof
A new Type B vent runs from the appliance draft hood or collar up to a listed cap above the roof. Along the way it needs firestop spacers at ceilings, an attic insulation shield where it crosses insulation, supports, roof flashing and a sealed storm collar.
We size and lay out the route to the appliance manual and the fuel gas code, using parts from one listed Type B system. The height above the roof follows the code's rules for the roof and nearby walls. Each stage is checked before ceilings and roof are closed up.
Working on a vent in the attic
Attic sections of a gas vent are often the ones exposed to insulation, storage, pests and later building work. They are also where supports and firestops are most likely to have been disturbed.
We check attic access before the visit and bring lighting and protection for the work. The route is followed from the ceiling crossing to the roof, looking at supports, joints, shields and clearances. Findings are recorded section by section, with anything we could not reach noted as not seen.
Vent connectors on natural-draft appliances
A vent connector links a natural-draft appliance to its gas vent or chimney, unless the vent attaches directly to the appliance. The fuel gas code requires connectors to be made of noncombustible, corrosion-resistant material able to handle the vent gas temperature and resist damage.
We check the connector for its material, joints, slope and support, and for clearance to combustibles. A connector that is corroded, loose or made of the wrong material is replaced with one that meets the code and the appliance manual. The finding and the replacement are recorded.
The gas venting scope you approve
- Termination clearances against the manual
- Supports, straps and wall bands
- Gas vent inside a masonry chimney reviewed
- Written record of the vent work
Direct-vent and B-vent questions we hear
Do you check the vent connector on natural-draft units?
Yes. The connector joins a natural-draft appliance to its vent, and the fuel gas code requires noncombustible, corrosion-resistant material able to handle the vent gas temperature. We check its material, joints, slope, support and clearance, and quote a replacement where it fails.
Can Type B vent be used on any gas appliance?
No. The vent maker lists Type B vent for appliances with draft hoods and others listed for Type B vent. It is not for appliances that can be converted to burn solid or liquid fuels. The appliance manual confirms which vent applies.
What records do I get after vent work?
A written record of the work that lists the appliance, the vent maker and system, and the route. It also covers the parts replaced, the checks made and anything that stayed concealed or outside the scope.
More Ways to Care for Your Fireplace
- Ventless Gas Fireplace ServiceService the identified vent-free appliance without bypassing its required safety components.
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo