Venting for gas fireplaces in Richmond Heights, checked end to end
When a vent issue means the fireplace should stay off, we say so and explain what would clear it.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When the gas fireplace vent is the suspect
- Termination cap bent or crushed
- Plants grown over the termination
- A new deck built close to the vent
- Flashing lifted around a roof vent
Jump to
Keeping a gas fireplace vent sound
Water collecting at a wall termination
Some manuals ask for a horizontal termination cap to slant slightly downward so that moisture inside it can drain out. A cap set level or tilted back toward the house can hold water, which may run back along the pipe or into the wall.
We check the angle of the termination against the manual and look for staining on the wall and pipe below it. Where the cap or the last section was set wrongly, it is reset to the instructions. Any water damage to the wall behind is listed for the appropriate trade.
Unlisted decorative shrouds over the cap
Decorative shrouds and covers over terminations are allowed only when listed for the vent system. One manual adds that a decorative cover can increase the clearances the cap needs, and refers to the shroud's own instructions.
If a termination has been fitted with a homemade cover or one from another product, we explain why it should come off. The listed decorative cap for your system can be quoted instead, with its clearances checked. We do not leave an unlisted cover on a vent we have worked on.
Replacing damaged B-vent pipe sections
Type B vent sections can corrode, dent or separate, particularly in attics and where they pass through the roof. A damaged section is replaced with the listed part from the same Type B system, joined with its locking feature.
Where a section was not listed for the appliance, or the whole run is past repair, we explain whether a full replacement is the better option. The estimate separates a single-section repair from a new run. Firestops, shields and supports disturbed during the work are refitted as the instructions show.
Outside air kits on natural-draft units
An outside air kit, where the model accepts one, brings combustion air in from outdoors rather than from the room. The maker of one such model recommends the kit and makes it mandatory under negative pressure, to support performance and to help stop combustion gases spilling.
If a draft check shows spillage and the house runs at negative pressure, we look at whether an outside air kit is listed for your model. Its inlet position and route are planned like any other vent part. The kit's control, which can be closed when the fireplace is not in use, is shown to you afterwards.
The gas venting scope you approve
- Accessible joints checked for full engagement
- Corrosion or separation along exposed pipe
- Supports, straps and wall bands
- Written record of the vent work
Direct-vent and B-vent questions we hear
Will you check the roof flashing around a vertical vent?
Yes, as part of the vent route. We look at the flashing, storm collar and sealant around the pipe where the roof can be reached safely. Roofing work beyond the flashing is referred to a roofer and priced by them.
What records do I get after vent work?
A written record of the work that lists the appliance, the vent maker and system, and the route. It also covers the parts replaced, the checks made and anything that stayed concealed or outside the scope.
Is vent repair part of a gas fireplace service visit?
No. A service visit includes a look at the termination, but repairs to the vent are quoted under this venting service. That keeps appliance work and vent work clearly separated on the estimate.
More Ways to Care for Your Fireplace
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Smoke Chamber RepairRepair identified smoke-chamber surfaces with the access and material requirements clearly defined.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo