A prefab fireplace in Lauderhill, repaired within its listing
Smoke, rust or a sagging grate each have a cause. We find it before replacing the part it damaged.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Clues that a prefab chimney needs attention
- Smoke rolling out at the opening
- Gap between the unit and the hearth
- Loud banging or cracking during a fire
- No label or manual for the unit
Jump to
Refractory, firebox metal and chimney pipe explained
Reading the maker's parts list for your model
Most manuals close with a parts list that names each replaceable piece for that model. Panels, grate, screen, damper parts, air kit pieces and chimney components each carry their own name and part number. That list, not appearance, decides what goes back into the fireplace.
We check the list against what is in your firebox today. Sometimes a part has already been swapped for something that does not appear there. When that happens, we explain the difference and include the correct part as its own line on the estimate.
Mixed chimney brands in one run
Factory-built chimney makers state that their sections are not to be mixed with other brands. Joints are designed for their own mating parts, and a mixed joint may not seal or lock as tested. That can open a path for heat and smoke where the listing assumed none.
We read the markings on the sections we can reach. If more than one system is present, we explain which sections must change and what the run needs to be consistent again. The replacement run is quoted as one item, so you see the whole correction at once.
Panels that keep cracking after replacement
If refractory panels crack again soon after replacement, the cause may lie elsewhere. Overfiring, a grate sitting too close, a missing retainer or water reaching the panels can each shorten their life.
We look for the cause before replacing the same panel again. That can mean checking the grate, the size of fire you usually build and the chimney top. Fixing the cause first protects the new part and saves you a repeat repair. Tell us how long the last panel lasted and how the fireplace was used in that time.
Sealant only where the manual allows it
Manuals specify where sealant goes, such as between the outside air hood and the house wall, and which kind suits the heat. Caulk or foam in the wrong place can block air spaces or fail under heat.
We remove sealant that sits where it should not and replace it only as the manual describes. Foam packed around a chimney where it passes a ceiling is not a firestop. The listed firestop goes back in its place, and the foam comes out.
What the free inspection checks on a prefab unit
- Maker's parts list for the model
- Firebox floor and wall metal
- Chimney sections and joint engagement
- Air space around the unit and pipe
What people ask before a prefab repair
Can the whole chimney on a prefab fireplace be replaced?
It can, with sections listed for that fireplace. One maker recommends replacing the chimney after a chimney fire, and heavy corrosion or crushed sections can also lead there. We quote the chimney as its own item, separate from any firebox work.
Do you repair the outside air kit on a prefab unit?
Yes, as part of the listed system. The code treats the outside air supply of a factory-built fireplace as a listed component. We check the control, the ducting and the hood outdoors, then replace damaged parts with those the manual names.
What is written down after my prefab fireplace repair?
You receive a written record of the work, naming the parts replaced, the areas we reached and anything we could not see. Store it alongside the manual, so whoever services the unit next can see what changed and why.
More Ways to Care for Your Fireplace
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Stone Chimney RepairRepair affected stone chimney surfaces with the supporting construction and visual match considered together.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo