Refractory panels and metal fireboxes repaired in Plantation
Tell us the maker and model if you can read them. We bring the right questions to your free inspection.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What goes wrong inside a metal firebox
- Bare metal where a panel fell away
- Warped firebox walls or floor
- Grate bars sagging or burned through
- Insulation touching the pipe in the attic
Jump to
Inside a factory-built fireplace repair
Listed parts keep the maker's terms intact
Owner manuals warn that unapproved parts, modifications and running the unit with parts missing can void the listing and the warranty. That warning applies to repairs as much as to the original installation. A quick fix with the wrong part can create a second problem.
Using the parts the maker names keeps the fireplace on the terms it was sold under. We explain where your unit stands, including any earlier change that may already affect it. The choice of how to proceed stays with you, with the reasons laid out.
The first fires after new refractory
New refractory and fresh paint need a few moderate fires to cure. Owner manuals mention an odor during those early fires and describe it as normal. Large, hot fires right after a panel replacement can stress the new parts.
We explain the break-in steps from your manual when the repair is done. Start with small fires, keep the damper fully open and give the room fresh air if the smell lingers. If smoke or odor continues well beyond the break-in fires, tell us so we can look again.
Rust on the metal inside the firebox
Rust inside a factory-built unit points to water. It may be entering at the top of the chimney, around the chase top or through a damaged cap. It may also be running down the outside of the pipe and into the unit.
We trace where the water comes from before judging the metal. Surface rust on a replaceable part can be handled with that part. Rust that has thinned or holed the firebox body is a different conclusion. Any repair to the chimney top or chase is a separate item, often under our chimney services.
The storm collar above the chase top
A storm collar wraps the pipe just above the chase top or roof opening. Its job is to turn rain aside before it reaches the gap around the chimney, and the manual shows how it is sealed. Once it loosens or cracks, water can track down the outside of the pipe.
We check the collar and its seal from the roof. Water that gets past it can reach the firebox as rust or drips. The collar is part of the chimney system and is replaced with the listed part. Repairs to the roof covering around the chimney are a separate job.
What the free inspection checks on a prefab unit
- Maker's parts list for the model
- Louvers and air passages kept open
- Termination cap and spark screen
- Operating guidance after the repair
Asked about zero clearance fireplaces in Plantation
Do you repair the outside air kit on a prefab unit?
Yes, as part of the listed system. The code treats the outside air supply of a factory-built fireplace as a listed component. We check the control, the ducting and the hood outdoors, then replace damaged parts with those the manual names.
How should I prepare for a prefab fireplace inspection in Plantation?
Let the fireplace go cold beforehand and leave its parts in place. Clear a path to the attic hatch if there is one. Set out the manual, receipts or notes from past repairs, and tell us what you noticed and when it started.
Who handles the wiring for a blower on my unit?
The blower kit itself is a listed part of the fireplace and follows the manual. Where it needs a new outlet or circuit, an electrician handles that as a separate item. We explain which part of the job belongs to whom before anything is scheduled.
More Ways to Care for Your Fireplace
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
- Chimney Animal RemovalAssess occupied chimney openings and plan appropriate follow-up cleaning or entry protection.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
- Chimney Sweep and Chimney CleaningArrange careful chimney cleaning in Miami with a defined scope, protected work area and useful findings.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo