Chimney stone repair for homes in Boulevard Gardens
Natural, veneer or manufactured, each stone assembly has its own repair, explained in plain terms.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What loose chimney stone can look like
- A stone that moves when touched
- White deposits washing out of the joints
- Stone buried in the roofing at the base
- Gaps where the stone meets the chimney top
Jump to
Our approach to stone chimney repair
A top that throws water past the stone
The top of a stone chimney needs a cap, crown or cover that throws water clear of the stone face. The Florida Building Code describes masonry chimney caps that slope to shed water and carry a drip edge. The stone installation guide shows the cap lapping over the top of the veneer.
If water is running off the top onto the stone, joints below will keep failing. We check the top and list any work there separately, so you can decide on the stone repair and the top together.
Putting original stones back
The best match for a stone on your chimney is usually the stone itself. Pieces removed with care can often be cleaned and reset. That keeps color, texture and weathering consistent across the repair. Reused stones also carry the same weathering as their surroundings, which new stone cannot copy.
We handle removed stones carefully and store them safely until they go back. Cracked or eroded pieces are set aside and discussed with you before anything is discarded. The written record notes which stones were reused and which were replaced, and where the new ones went.
A section of stone bowing outward
When part of a stone face bows outward, the stones have lost their hold on the wall behind them. Corroded ties, failed lath or a soaked backing are common reasons, and the bow tends to grow. Pushing a bowed section back without repairing the backing does not hold.
A bowing section can fall, so we assess it early and advise keeping people clear below. Repair usually means removing the affected area, repairing the backing and resetting the stones. The estimate describes the area and what we expect to find behind it, with the unknowns stated plainly.
Old, hard mortar in stone joints
Earlier repointing is sometimes done with a mortar much harder than the stone. National Park Service guidance explains why that harms masonry, since the stone becomes the weaker partner and takes the damage. Hard joints also tend to crack along the stone edge, letting water in behind them.
We look for chipped or flaking stone edges beside hard joints. Where old hard mortar can come out without harming the stone, we replace it with a more suitable mix. Where removal would damage the stone, we explain the options and their limits before any work begins.
How we itemize stone chimney work
- Scratch coat or lath repair behind adhered veneer
- Separate line for flashing work at the roof
- Roof and landscape protection during work
- Unused brackets and fixings removed or sealed
Answers on repointing chimney stone
Why are white deposits forming on my stone chimney?
White deposits usually mean water is moving through the stone or joints and leaving dissolved minerals behind as it dries. Brushing them off helps the look, but finding where the water enters is what stops them returning.
Do you cover open areas if the work takes more than a day?
Yes. Before we leave each day, any area where stones are off is sheltered from rain, and removed stones are stored safely until they go back. Loose debris goes with us rather than staying on the roof.
Can I keep using the fireplace during exterior stone work?
Exterior stone work seldom affects the fireplace. Where a repair reaches the chimney top or the inside of a framed chase, we say whether fires should wait until that section is closed up again.
More Ways to Care for Your Fireplace
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo