Chimney stone repair for homes in Hallandale Beach
Homes in Hallandale Beach get the same order of work from us: water first, backing next, stone last.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Stone and joint problems to point out
- Thin gaps around individual stones
- Stone buried in the roofing at the base
- Gaps where the stone meets the chimney top
- Loose stones above a door or walkway
Jump to
Stone chimney work explained
Joint profiles that match the stone around them
Mortar joints are finished in different ways. They may sit flush with the stone, be recessed, be rounded or be struck at an angle. The profile changes how the chimney looks and how water runs off each joint.
We match the existing profile unless it is shedding water badly, in which case we explain the alternative before starting. Joints are tooled once the mortar is firm enough to hold a shape, as the manufactured stone installation guide describes. Tooling too early smears the stone, and too late leaves a rough joint.
The line where chimney stone meets roofing
A stone chimney that rises through a roof needs flashing that turns water onto the roof. The stone should finish above the roofing, not sit in it. The manufactured stone installation guide shows the flashing extending past the chimney and the stone stopping above it.
We inspect this junction together with the stone. Flashing repair is a separate service with its own price. If stones must come off to reach the flashing, resetting them is included in the same plan, so neither job undoes the other.
Stone at the chimney corners
Corners take knocks and weather from two sides. On manufactured stone, corners are often formed with purpose-made corner pieces. On natural stone, corner stones are dressed to show two finished faces. Corners also show a mismatch more than flat faces do, so matching gets extra care there.
A loose or broken corner piece exposes the backing on two sides at once. We check every corner along its height. Replacement corners are matched to the product or shaped to fit, and set in a full bed like any other stone, with the joints tooled to match the faces on either side.
Joints where stone meets other materials
Where stone meets siding, trim or another finish, the joint needs to allow movement and stay sealed. The manufactured stone guide calls for flashing and sealant at penetrations and at transitions between materials. Old sealant is cut out completely before new material goes in, since fresh sealant does not hold well on old.
We check those joints for cracks, gaps and missing sealant. Resealing them takes little time and shuts off an easy route for rain. It is listed as its own item, with the materials named, so you can see what went into each joint.
What a stone chimney quote lists
- Replacement stones blended with the originals
- Weep openings cleared in anchored veneer
- Clearance kept between stone and roofing
- Unused brackets and fixings removed or sealed
Chimney stone questions with plain answers
Do you cover open areas if the work takes more than a day?
Yes. Before we leave each day, any area where stones are off is sheltered from rain, and removed stones are stored safely until they go back. Loose debris goes with us rather than staying on the roof.
What mortar do you use for repointing stone?
One chosen for the stone and the assembly. For natural stone, the mortar should not be harder than the stone. Manufactured stone follows its maker's guidance. We explain the choice rather than using one mix everywhere.
Why did stones on my chimney come loose?
Common causes include poor mortar coverage behind the stones, water in the backing, corroded lath or ties, and movement. The stone that came off often shows which cause applies, so we look closely at its back.
More Ways to Care for Your Fireplace
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
- Chimney Sweep and Chimney CleaningArrange careful chimney cleaning in Miami with a defined scope, protected work area and useful findings.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney Cap Installation and ReplacementProtect the chimney opening with a cap chosen for its fit, attachment and compatible system.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo