Stone chimneys in Sunset, reset and repointed with care
Your estimate separates stone resetting, repointing and any backing or flashing work.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Stone and joint problems to point out
- A stone that moves when touched
- Thin gaps around individual stones
- Caulk or foam from earlier quick fixes
- Loose stones above a door or walkway
Jump to
Stone chimney repair in plain terms
Raking out worn joints by hand
Repointing starts by removing deteriorated mortar back to sound material. National Park Service guidance on repointing warns that power tools can chip the edges of masonry units. With stone, a chipped edge cannot be put back. Joints are cleared to a consistent depth so the new mortar has a sound bond on every side.
We rake joints with hand tools where the stone is fragile or irregular, and use careful mechanical methods only where they will not harm it. Each joint is cleaned of dust and dampened before new mortar goes in, so the fresh mortar grips the stone on both sides.
The joint where stone meets the chimney top
Where stone meets a crown or cover, a clean joint and a drip keep water from running behind the top courses. That junction often opens as the materials expand and contract at different rates. Water entering there can travel down behind several courses before it shows.
We check it on every side. Failed sealant or mortar is removed and replaced with a material suited to both surfaces. If the top above needs work, it is priced separately, and the stone repair is sequenced to meet it so the two finish at a tight, weather-shedding joint.
Keeping rain off fresh stone work
Heavy rain on fresh joints can wash mortar out of them and stain the stone below. New setting beds also need time before they are soaked. Fresh joints darken and weaken if rain reaches them too soon.
We watch the forecast and protect fresh work when rain threatens. Opened areas are covered before we leave each evening, and loose stones are stored safely off the roof. If weather interrupts the sequence, we tell you how it changes the plan and when we expect to return. A delayed finish is better than joints that wash out.
Maintenance visits for a stone chimney
A stone chimney benefits from a periodic look at its joints, any loose stones, the top and the drainage edge. A single loose stone found early is a small job, and so is a short run of open joints.
Ask about maintenance visits once your repair is complete. We check the repaired area and the rest of the chimney, then tell you what needs attention and what can safely wait. Visits are booked whenever you want one, and each starts from the record of what we repaired.
Pieces of a stone chimney repair scope
- Cleaning stone backs and setting surfaces
- Replacement stones blended with the originals
- Hose water test when the job calls for it
- Unused brackets and fixings removed or sealed
Chimney stone questions with plain answers
Will new mortar joints match the old ones?
We match color, texture and joint profile as closely as materials allow and judge samples once they are dry. New joints can look fresher at first and tend to settle in as they weather.
Why did stones on my chimney come loose?
Common causes include poor mortar coverage behind the stones, water in the backing, corroded lath or ties, and movement. The stone that came off often shows which cause applies, so we look closely at its back.
Will the repaired area stand out from the rest of the chimney?
New mortar and fresh stone faces can look brighter at first. We blend by reusing original stones where possible and matching the joints. The difference tends to soften as the repair weathers.
More Ways to Care for Your Fireplace
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo