Stone chimneys in Westview, reset and repointed with care
A loose stone overhead is a hazard, which is why we look at it first on the visit.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Stone and joint problems to point out
- A stone that moves when touched
- Thin gaps around individual stones
- Rust streaks running down the stonework
- A stone face pulling away from the wall
Jump to
Stone chimney repair in plain terms
Solid stone, anchored veneer or adhered veneer
Stone on a chimney can be built in more than one way. Solid stone masonry carries its own weight. Anchored veneer is a stone face tied back to a wall behind it with metal ties. Adhered veneer, natural or manufactured, is set in mortar over a prepared backing.
The repair follows the construction. A loose stone in solid masonry is a question of joints and bedding. A loose piece of adhered veneer raises questions about the scratch coat, lath and barrier behind it. We identify which you have before we quote, and we explain how we reached that view.
Confirming the water route with a hose
Water can reach the inside of a house by more than one route. When the job calls for it, a hose water test wets the chimney section by section with someone watching indoors, so the stone can be told apart from the top and the roof.
It takes patience, so we suggest it only when the answer will change what we repair. We explain the plan before we start and the result afterward. The estimate then reflects what the test showed rather than a guess about the water path.
Keeping rain off fresh stone work
Heavy rain on fresh joints can wash mortar out of them and stain the stone below. New setting beds also need time before they are soaked. Fresh joints darken and weaken if rain reaches them too soon.
We watch the forecast and protect fresh work when rain threatens. Opened areas are covered before we leave each evening, and loose stones are stored safely off the roof. If weather interrupts the sequence, we tell you how it changes the plan and when we expect to return. A delayed finish is better than joints that wash out.
Lifting stones to reach the flashing
On some chimneys, the flashing at the roof is tucked behind the lowest stones. Repairing it properly can mean lifting those stones and setting them back afterward. Those stones are numbered or laid out in order so each goes back where it came from.
When that is the case, the flashing work and the stone resetting are planned together, so the flashing is finished before the stones cover it again. Flashing is its own service with its own line on the estimate, and the stone work needed to reach it appears right beside it.
What a stone chimney quote lists
- Weep screed cleared or reset at the base
- Roof and landscape protection during work
- Sealant joints at changes of material
- Unused brackets and fixings removed or sealed
Your stone chimney questions
Why not just glue a loose stone back in place?
Adhesive is not a substitute for a proper mortar bed on an exterior wall. A glued stone can let go again, and the glue can block the drainage behind it. We reset stones the way the assembly was meant to hold them.
Do you need roof access to repair a stone chimney?
For most chimneys, yes. The top, the upper stones and the roof junction are reached from the roof. We protect the roof covering, plan safe access and tell you if any area cannot be reached.
Why did stones on my chimney come loose?
Common causes include poor mortar coverage behind the stones, water in the backing, corroded lath or ties, and movement. The stone that came off often shows which cause applies, so we look closely at its back.
More Ways to Care for Your Fireplace
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
- Chimney Animal RemovalAssess occupied chimney openings and plan appropriate follow-up cleaning or entry protection.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
- Smoke Chamber RepairRepair identified smoke-chamber surfaces with the access and material requirements clearly defined.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo