Chase cover repair or a new cover in Lauderdale Harbours
Homes in Lauderdale Harbours with framed chimneys get a cover measured on the roof, not guessed from the yard.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When a chase cover in Lauderdale Harbours needs replacing
- Loose screws along the skirt
- Storm collar slipped or missing
- Chimney pipe leaning in its collar
- Cover smaller than the chase top
Jump to
Chase cover details that decide the result
Finding the label on the chimney or fireplace
Factory-built fireplaces and chimneys carry labels with the maker, model and listing. The fireplace label is often behind a panel near the opening or inside the surround. The chimney pipe may carry its own label in the attic or inside the chase.
If you can find the fireplace label safely, read us the details when you call. Please do not remove panels you are unsure about or climb into tight spaces. We find it during the visit if needed. The label tells us whose instructions govern the top of the chase.
Checking the chase from the ground
A good deal can be seen without a ladder. Stand back from the house and look at the top of the chase with binoculars if you have them. A cover that sits unevenly, a skirt lifting away, streaks down the siding or a leaning cap are all visible from the yard.
Indoors, check the ceiling and walls near the fireplace for stains and the fireplace itself for corrosion or water. Jot down what you notice and the date. Share it when you book, and we will start the visit with the part your notes point to.
Chase top work inside the code's HVHZ
Broward County sits inside the zone the Florida Building Code calls HVHZ. Roof and exterior work in that zone follows its own set of provisions in the code.
A chase cover replacement may or may not touch the roofing itself. If the job reaches the flashing at the chase base, the roof covering or new cladding, ask which provisions apply. Do that before you approve it. We tell you what we understand the specific work requires, and we do not claim a product approval that a product does not carry.
Screws that hold up in sea air
In salt-laden air, the screws through the skirt need watching. They carry little metal, and once they corrode through, the skirt can lift in the next strong wind.
We use fasteners that suit the cover metal and the exposure, and we drive them into sound framing. On maintenance visits near the water, the fasteners are among the first things we check. Replacing a few corroded screws early is much simpler than refitting a cover that has worked loose.
Measured before a chase cover is ordered
- Outside size of the chase top
- Cap on the pipe checked for reuse
- Support under a wide cover
- Finish or paint on the new metal
Answers about chase covers in Lauderdale Harbours
Can a corroded cover be patched rather than replaced?
Small repairs can buy time on a cover that is otherwise sound. A cover with holes, a dished middle or thin metal throughout usually needs replacing, because patches over corrosion tend to trap water. We show you the condition before you choose.
Can the existing cap stay on the chimney pipe?
It can, if it is sound and is the cap listed for that chimney. We check it while we are up there. A damaged cap, or one that does not belong to the system, is noted as a separate item for you to decide on.
Why is there a gap between the storm collar and the cover?
Some chimney systems call for air spaces at the chase top so the chase stays ventilated around the pipe. Where the instructions show them, those gaps are part of the design, not a fault, and we keep them when fitting the new cover.
More Ways to Care for Your Fireplace
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo