Chimney chase cover replacement for homes in Sunrise
We trace where the water got in first, so a new cover is proposed only when it is the cause.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What a worn chase cover looks like in Sunrise
- A sagging or dished chase top
- Rust flakes inside the fireplace
- Metal banging on the chase in wind
- Cracked sealant around the pipe
Jump to
Chimney chase cover work in Sunrise
Measuring the chase top properly
A chase cover is measured on the roof, with a tape and a sketch of the top. We record the outside size of the chase, where each pipe sits and how large it is. The skirt depth goes down too, along with anything that breaks the rectangle, such as trim or a step in the wall.
Cover makers publish worksheets for exactly these measurements, and they warn that the dimensions must include clearances. A measurement guessed from the ground or copied from the old cover can carry old mistakes forward. The estimate lists our measurements so you can see what the new cover is built to.
Tar and cement patches on old covers
Old covers often carry patches of roofing tar, cement or tape over holes and seams. Those patches can stop a drip for a while, but they also hold moisture against the metal and hide how far the corrosion has spread beneath them.
When we see patches, we look at their edges for cracking and at the metal around them. A cover with several patches is usually near the end of its life. We describe what the patches are covering once we can see it, and we explain why another patch may not be the sensible next step.
Soft siding just below the top edge
If the siding near the top of the chase feels soft, looks swollen or has paint bubbling off it, water has probably been getting behind it. The top few courses are usually the first to show it, because they sit right under the edge of the cover.
Do not press or pry at it from a ladder. Tell us what you see, and we look at it during the inspection. Siding and sheathing repair belong to chase repair, which is quoted separately from the cover. Replacing the cover without dealing with soaked wood beneath it leaves the problem in place.
Hose testing a chase top leak
Sometimes the source of a chase leak is not obvious from looking. Where the job calls for it, we run a hose water test. Water is run over one part of the chase top at a time while someone watches inside for it to appear.
We use a hose water test only when the job calls for it, not as a routine step. We explain why it is needed, what it involves and whether it is included in the estimate. The result can show which part lets water in, so the repair addresses that part and not a guess.
Chase cover scope, line by line
- Outside size of the chase top
- Sheathing damage noted as its own item
- Fastener type and spacing on the skirt
- Old metal and sealant hauled away
Chase cover FAQs for homes in Sunrise
Why does water sit on top of my chase cover?
Flat covers, and covers that have sagged, hold water instead of shedding it. Standing water speeds up corrosion and can eventually find a way into the chase. A replacement with cross-breaks or a slope, plus a drip edge, moves the water off.
Do I need to be home while the chase cover is replaced?
Not for all of it. The work is on the roof, but we may want to look at the fireplace and any ceiling stains inside. Tell us when booking how to reach you and how to access the property.
Is a same-day chase cover fitting available?
Same-day service is available when the schedule allows, but most covers are made after measuring. We tell you at the inspection whether a same-day fitting is realistic for your chase and how the top is protected meanwhile.
More Ways to Care for Your Fireplace
- Chimney WaterproofingTreat suitable chimney masonry after checking the surface, repair needs and product requirements.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Hurricane and Storm Damage Chimney RepairAssess storm-related chimney concerns and distinguish temporary protection from permanent component repair.
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo