Chase cover repair or a new cover in Sunset
Homes in Sunset with framed chimneys get a cover measured on the roof, not guessed from the yard.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs a chase cover in Sunset is failing
- Old tar or cement patches on top
- Chimney pipe leaning in its collar
- Cracked sealant around the pipe
- Cover smaller than the chase top
Jump to
The chase cover job, from measure to seal
Copper covers and the metals they meet
Copper chase covers are often chosen for appearance, and they weather to a darker tone over time. Copper does not sit comfortably next to every metal. Where copper and another metal touch and stay wet, one of the two can corrode faster than it would on its own.
If you like the idea of copper, tell us early. We look at the pipe, the storm collar, the cap and any flashing nearby, and we explain whether copper can be isolated from them. The estimate names the copper cover and the fasteners chosen to suit it, so the decision is made with the details visible.
Checking the chase from the ground
A good deal can be seen without a ladder. Stand back from the house and look at the top of the chase with binoculars if you have them. A cover that sits unevenly, a skirt lifting away, streaks down the siding or a leaning cap are all visible from the yard.
Indoors, check the ceiling and walls near the fireplace for stains and the fireplace itself for corrosion or water. Jot down what you notice and the date. Share it when you book, and we will start the visit with the part your notes point to.
Tall chases and wind at the top
A chase that rises well above the roof catches more wind than a short one. Its cover takes stronger gusts, and loose edges or weak fasteners show up sooner. Tall chases can also sway slightly if the framing is not braced as it should be.
If your chase is tall, mention it when you call. We look closely at the fastening, the skirt and the framing at the top. Where the cover needs more fasteners than the old one had, or the framing needs attention, the estimate says so and explains why.
Unlike metals on a chase top near the coast
Where unlike metals touch, salt-laden moisture speeds up the corrosion between them. A stainless cover held with plain steel screws, or copper touching a galvanized storm collar, can leave one part failing long before the rest. A small part fares worst when it is the metal that corrodes, such as a plain steel screw.
Near the coast, we look closely at every metal that meets at the chase top: the cover, the screws, the collar, the storm collar and the cap. We match them where we can and explain how the parts are kept apart where we cannot. The written record lists each metal used.
Your chase cover quote in Sunset, itemized
- Air spaces at the pipe kept open
- Old cover and fasteners removed
- Screened lid section where listed
- Workmanship warranty on the fitting
Answers about chase covers in Sunset
How can I tell whether my chimney has a chase cover?
If the chimney is a boxed structure finished in siding or stucco with a metal pipe at the top, it has a chase and almost certainly a cover. A brick or block chimney with clay flues has a crown instead. We confirm which during the free inspection.
Should I paint my old chase cover to slow the corrosion?
Paint can slow surface corrosion on a cover that is otherwise sound, but it does not close holes or fix a flat top that holds water. We tell you honestly whether paint is worth it or the cover is past that point.
What should I tell you when I call about the chase?
Describe what you see from the ground, any stains or water inside and whether the fireplace is used. Mention the chimney maker if you know it. With that, we can plan the visit to your home in Sunset and bring the right gear.
More Ways to Care for Your Fireplace
- Smoke Chamber RepairRepair identified smoke-chamber surfaces with the access and material requirements clearly defined.
- Stone Chimney RepairRepair affected stone chimney surfaces with the supporting construction and visual match considered together.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo