Spalled brick replacement on chimneys in Imperial Point
Each replaced unit carries our workmanship warranty and is noted, brick by brick, in your written record.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs of brick damage on chimneys in Imperial Point
- Brick cores showing where faces fell
- Spalled brick just above the roofline
- Stains inside beside the chimney
- Pitted brick from past harsh cleaning
Jump to
Choosing replacement brick for a chimney
What spalling brick repair involves on a chimney
Spalling brick repair replaces units whose face has flaked, popped off or cracked through. The damaged brick is cut out, the opening is cleaned and a matching brick is set in fresh mortar. Sound brick around it stays in place.
The other half of the job is the cause. Water is usually part of the cause. We look for where that water comes from and explain it alongside the replacement. New units should not be asked to survive the conditions that broke the old ones.
Fresh joints that settle in color over time
New mortar around a replaced brick often looks brighter than the old joints at first. Federal preservation guidance explains that weathered mortar shows more of its sand, and fresh mortar has not weathered yet.
We match to sheltered, less weathered areas of the existing joints, because that is what the new joints will come to resemble. Staining new mortar to force a match is generally not recommended. In most cases, time closes the gap. Knowing that in advance means a slight contrast on the day of the work need not cause concern.
The order of repairs around damaged brick
When a chimney needs several repairs, the order matters. The water source, whether crown, cap or flashing, is usually fixed first. Loose top courses are dealt with before any new crown. Damaged bricks lower down are then replaced.
Working in that order means new brick goes into a chimney that is no longer being soaked. We explain the sequence on your estimate and show which items you have approved. If you delay one item, we explain how it affects the others.
Plain questions to ask about brick work
A good brick replacement proposal should answer a few plain questions. Ask which units will be replaced and why, what caused the damage, how the new brick will be matched and what mortar will be used.
Also ask what the work leaves out. Brick replacement does not fix a failed crown, loose flashing or eroded joints elsewhere. We answer those questions in writing on the estimate, so you know exactly what you are approving. Clear answers now prevent misunderstandings once the work starts.
Spalled brick items on a written estimate
- Sample of the proposed brick match
- New brick buttered and set in place
- New units toothed into the bond pattern
- Workmanship warranty on agreed brick work
What people ask about replacing bricks
Why do the faces of chimney bricks come away?
Usually because water gets into the brick and something stops it drying out through the joints. Soluble salts can crystallize under the face, and hard mortar or a film coating can make it worse. We look for the source before replacing units.
How do you match new brick to an older chimney?
We compare size, color, texture and the range of shades in the wall, and we can set out a sample to judge the match. Finding a close brick can take some searching. New brick may look fresher at first.
Will the new bricks look different from the old ones?
At first they may, because the old brick has weathered and the new mortar is fresh. A careful match of size, color and texture keeps the difference small, and it usually softens with time. We show you the proposed brick before approval.
More Ways to Care for Your Fireplace
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Chimney WaterproofingTreat suitable chimney masonry after checking the surface, repair needs and product requirements.
- Chimney Flue RepairAssess repairs to damaged existing flue linings and distinguish them from a new liner installation.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Firebox RepairRepair the damaged fireplace chamber using an approach suited to masonry or manufactured components.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo