Worn chimney cap replacement in Flamingo Park
Upfront pricing for chimney cap work in Flamingo Park, with no hidden fees and a written record of the job.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Chimney cap trouble you can spot in Flamingo Park
- Rattling from the chimney top in wind
- Rust streaks running down from the cap
- Cracked flue tile under the cap
- Cap shifted after a strong storm
Jump to
What goes into a new chimney cap in Flamingo Park
Measure the tile, not the hole
For a cap that clamps onto a flue tile, the outside size of the tile matters more than the opening inside it. Tile walls vary in thickness, and a cap sized to the inside of the flue can end up too small to slide over. Rectangular tiles also need both sides measured.
We take those measurements on the roof during the free inspection. Where the tile is chipped, out of square or wrapped in old mortar, we note it, because that changes the fit. The estimate lists the sizes we measured, so the cap that arrives is the cap that fits your flue.
Fasteners that suit the cap metal
Where two unlike metals touch and stay wet, one of them tends to corrode faster than it would on its own. Corrosion guidance for galvanized steel adds that a small piece of the weaker metal against a large area of the other is the worst pairing.
On a cap, that small piece is often the fastener. A plain steel bolt through a stainless band or a copper lid can rust away and leave the cap loose. We use the fasteners the cap maker supplies or specifies, and we record what was used. Ask about fasteners when you compare cap proposals.
How high the lid sits above the flue
The gap between the top of the flue and the underside of the lid affects both rain and smoke. Too little gap can choke the flue. Too much can let rain blow in at an angle. The right height depends on the cap design and the flue it covers.
Brick industry design guidance says the maker of a manufactured rain cap should be asked for its effect on flow through the chimney. We work from that information when choosing a cap. If your current cap sits noticeably low or high, we note it, and the proposal explains the height chosen for the new one.
Caps that mount on a liner's top plate
Where a chimney has been relined with a stainless liner, the liner usually hangs from a top plate on the crown. The liner maker supplies a cap that fastens to that plate or to the liner itself. One maker's instructions show the cap removed by its screws for cleaning.
If your chimney has a liner, the replacement cap should be the one the liner system calls for, not a generic cap clamped over the plate. We identify the liner and its top plate before recommending anything. The written record then notes the liner system, so a future cap can be matched without guesswork.
Chimney cap scope, item by item
- Cap style suited to the mounting surface
- Draw check once the cap is on
- Handover on screen cleaning and lid removal
- Separate line for damper or chase cover work
Common chimney cap questions, answered
Do you clean up after replacing the cap?
Yes. We take away the old cap and its hardware, clear debris from the roof area and haul it off. If the flue has to stay open overnight for any reason, we cover it at the end of the work day.
Can a cap be fitted over a damper at the chimney top?
Some top-mounted dampers already act as a cap, and some are made to sit beneath one. The damper maker's instructions decide which. Tell us if your chimney has a cable-worked damper at the top so we check it before recommending a cap.
Do you work on chimneys that serve more than one appliance?
Yes. When one chimney carries flues for a fireplace and another appliance, each flue keeps the termination its appliance calls for. We identify what each flue serves before choosing one cap or separate ones.
More Ways to Care for Your Fireplace
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Spalling Brick Repair and Chimney Brick ReplacementReplace deteriorated chimney bricks while retaining suitable surrounding masonry.
- Wood-Burning Fireplace Insert InstallationFit a wood-burning insert after assessing its host fireplace and full connection requirements.
- Chimney TuckpointingRenew deteriorated mortar joints around chimney bricks that can appropriately remain.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo