Chimney crowns assessed and repaired in Lauderdale Isles
Tell us where the water shows up, and we check whether the crown is part of its path.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When the crown at the chimney top needs work
- Crumbling edges along the crown overhang
- Dried or split caulk around the flue
- No overhang past the brick face
- Crown and brick separating along the top course
Jump to
Getting the chimney crown right in Lauderdale Isles
What a coating cannot hold together
The coating data sheet we follow says the surface must be structurally sound and not loose. Its product warranty also excludes spalling and faulty construction. That tells you the product protects a good crown rather than rebuilding a bad one.
If your crown has crumbling edges, hollow patches or sections that move when pressed, we do not recommend a coating over them. Rather than a membrane over failing concrete, we remove what is unsound and discuss a new crown. You see both options explained before any decision is made.
A gap between the crown and the brick
Sometimes the crown separates from the top course of brick. A dark line opens along the joint, or the crown rocks slightly when pressed. Water can then run under the crown and into the wall.
The gap may come from failed bedding mortar, movement or loose brick below. We look at which one it is before proposing work. A crown that is sound but loose may be reset. A crown sitting on loose brick needs the masonry addressed first, which is priced as its own item.
Stone and metal tops on masonry chimneys
The residential code allows the top of a masonry chimney to be concrete, metal or stone. Concrete is the material people usually picture, but a stone slab or a metal top is sometimes used. Each needs slope, a drip edge and a sealed break at the flues.
If your chimney has a stone or metal top, we assess it against the same requirements. A stone slab may need its joints resealed or its bed repaired. A metal top may need fasteners or seams addressed. We explain what applies before any work is proposed.
Thin edges and broken crown corners
Crown corners take weather from two sides and can be the first place to break. Where the concrete thins near the edge, small pieces loosen and fall. The broken edge then lets water into the top of the brick.
A broken corner can sometimes be rebuilt with a compatible repair material if the rest of the crown is sound. If several corners have gone or the edge is thin all the way round, we explain replacement instead. Coating over a crumbling edge only hides it for a short time.
Separate lines for crown, cap and flue
- Bond-break layer under new concrete
- Curing time and weather protection
- Written record of completed crown work
- Separate lines for cap or liner defects
Chimney crown work, questions and answers
When can the fireplace be used again after crown work?
That depends on the product and the weather during curing. We give you waiting instructions for the material actually used on your chimney. Follow them even if the surface looks dry, because curing continues after the top looks finished.
Why does a new crown need to overhang the brick?
An overhang with a drip edge throws water clear of the brick face instead of letting it run down the chimney. The code also calls for a drip edge on the top of a masonry chimney. Without one, water can keep soaking the top courses.
Does the workmanship warranty cover crown repair in Lauderdale Isles?
Yes, the agreed crown work carries our workmanship warranty. Your written record states what was done, which helps if a question comes up later. Trouble from a separate part, such as a failed cap or flashing, is discussed as its own item.
More Ways to Care for Your Fireplace
- Chimney Animal RemovalAssess occupied chimney openings and plan appropriate follow-up cleaning or entry protection.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo