Flashing repair at the roof and chimney joint in Cutler Bay
Our family team explains what the flashing needs in Cutler Bay and leaves the decision with you.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Marks and gaps that suggest flashing failure
- Counter flashing standing away from the brick
- Rust streaks on roofing below the chimney
- Wet attic insulation around the stack
- Metal bent or lifted after strong wind
Jump to
Flashing work sized to the roof and chimney
Base and counter flashing work as a pair
Flashing at a chimney is usually two layers of metal rather than one. The base pieces lie on the roof and turn up against the brick. The counter flashing comes down from the chimney and laps over them. Because the two layers overlap instead of joining, each one stays with its own surface.
When we assess the junction on a home in Cutler Bay, we check both layers separately. A sound base piece under a loose counter piece needs a different repair from the reverse. The estimate names which layer fails and on which face, so you can see why the scope is sized the way it is.
Rain that arrives from the side
In a storm, rain does not only fall straight down. Wind drives it sideways against the chimney, where it can reach the top edge of the counter flashing and the joints above it. A junction that stays dry in calm rain may leak only in wind.
Tell us whether the water in your home in Cutler Bay appears only in wind from a certain quarter. A pattern like that singles out one face of the chimney. We check the upper edge of the metal on that face with care, because a joint that sheds falling rain can still let driven rain through.
Flashing against a stucco finish
Where a chimney is finished in stucco, the counter flashing has to meet cement plaster instead of open brick joints. A reglet can be cut into the stucco, or the metal may be set with a stop that the plaster finishes against. Each approach needs the finish around it to be sound.
Cracked or hollow stucco near the roof line can let water in above the metal. We check the finish close to the junction and say whether stucco repair should come first. Stucco work beyond the flashing line is its own item, priced and approved separately.
Testing the junction with a hose
When the job calls for it, a hose water test can show whether the flashing is the path. Water is run over one part of the chimney at a time, starting low on the roof and working upward, while someone watches inside. Each stage runs long enough to give water a chance to appear.
The order matters, because water sprayed high on the stack runs down over everything below it. A test is not needed on every job. We explain beforehand why we think it will help, what it may wet inside and how the area will be protected.
Checked at the roof junction before quoting flashing
- Old roof cement cleaned back or removed
- Debris cleaned up and hauled away
- Workmanship warranty on installed flashing
- Separate pricing for any added item
Flashing questions before you book in Cutler Bay
How do you know the flashing is the source of the water?
We compare where the water appears with what we see at the junction, in the attic and at the top of the chimney. When the evidence is unclear, a hose water test may help if the job calls for it. The findings say what points where.
Do you seal chimney flashing with roof cement?
Not as the main seal. Roof cement is a roofing patch material, and a flashing joint should rely on lapped metal with sealant at the reglet and hidden laps. Where old cement hides the metal, we clean it back to see what is underneath.
Does the flashing need checking if the fireplace is not used?
Yes. The chimney still passes through the roof, and the flashing keeps water out whatever happens in the firebox. An unused chimney can leak for a long time unnoticed, so a look during a maintenance visit is worthwhile.
More Ways to Care for Your Fireplace
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
- Fireplace Hearth RepairRepair the hearth surface after considering the supporting assembly and fireplace requirements.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo