Flue repair or relining, decided in Lauderdale Harbours
Approve the flue work within 72 hours of the free inspection to save 10% on the tiles and joints.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Signs of a failing flue lining in Lauderdale Harbours
- A cracked top tile above the crown
- Weaker draft than the fireplace used to have
- Cracks in the chimney brick near the top
- Glazed deposits hiding the tile surface
Jump to
How a damaged flue gets repaired in Lauderdale Harbours
Damage found deep in the flue
Some defects sit far below the top, around offsets or near the smoke chamber. They are harder to see and harder to reach. A repair method has to reach the actual defect to be of any use.
We describe how deep each defect is and how it would be reached. A treatment that cannot get to the damaged section should not be described as having repaired it. If no repair can reach it properly, the estimate explains why relining is the recommendation instead. Depth is described in plain terms, such as below the roofline or near the chamber.
Rain entering the flue from the top
An uncapped or poorly capped flue lets rain run down the inside of the tiles. Water carries combustion residue into the joints and helps break them down over time. The joints near the top usually see the most of it.
When we repair a flue, we also look at how water reaches it. A cap is often part of the answer, and it is quoted as chimney cap work on its own line. Repairing the joints while leaving the top open to rain leaves the cause in place.
Replacing a tile deep inside the chimney
Reaching a damaged tile deep in the chimney can mean opening the masonry from the outside or from a room. That is a substantial job, with its own structural and finishing work. Now and then it is the one practical way to replace a specific tile.
We explain when this approach would be needed and what it involves. Often another route, such as resurfacing or relining, achieves a sound flue with less disruption. The estimate lays out the options so you can compare them before deciding. Any wall opened for access is closed and finished as part of that scope.
Odors from a damaged flue
A damaged lining can let deposits collect behind the tiles, and moisture reaching them can carry odor into the room. Odor has other possible causes too, including air moving down the chimney and deposits inside the flue itself.
We look at the lining as one possible source among several. If it is involved, we explain how the repair would help. If the cause lies elsewhere, we say which part of the system is responsible and do not stretch the flue repair to cover it. An odor that changes with the weather or the wind is worth describing when you call.
Flue repair scope written out in full
- Mortar ridges cut back from the passage
- Bond break restored at the crown
- Repair debris cleaned up and hauled away
- Crown or cap work quoted on its own line
Chimney flue repair questions and answers
How do you know whether my flue qualifies for resurfacing?
The repair system's instructions set the conditions: sound, clean and dry tiles, cracks that will not let pieces loosen, protruding mortar removed, and enough flue size left for the appliance or fireplace. We check each one and tell you the result.
Do you repair flues that serve gas-fired appliances?
Where the repair system's listing covers the appliance, yes. Some systems exclude gas appliances that vent under pressure or condense their flue gases. We check your appliance against the listing before recommending any method.
How do I compare flue repair quotes?
Compare the method and product named, the sections covered, the preparation included and the curing guidance. Ask what each quote leaves untouched. A lower total that skips cleaning or loose tile removal describes a different job.
More Ways to Care for Your Fireplace
- Chimney Cap Installation and ReplacementProtect the chimney opening with a cap chosen for its fit, attachment and compatible system.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo