Chimney liner installation for fireplaces in Three Lakes
Our family-owned team explains whether relining is the right step, and says so plainly when it is not.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Observations that start a relining assessment
- No lining visible from the chimney top
- Rust holes in an old liner
- A planned switch from gas to solid fuel
- Weak draft after an appliance change
Jump to
What goes into relining your chimney
The lining types the code accepts
The code names a short list of acceptable linings for a masonry chimney. It includes clay flue tile, a listed chimney lining system, a factory-built chimney unit listed for use inside masonry, and other approved materials that resist heat, corrosion and condensate. Each one carries its own installation rules.
A listed lining system is designed to go into an existing masonry chimney, which is why relining proposals often take that route. Our estimate still names the option it uses. If another route suits your chimney better, we explain why and describe what that route would involve.
Keep the flue at least as large as the connector
The code does not allow a chimney flue to be smaller in area than the connector coming from the appliance. A liner that narrows the passage below that size works against the equipment it is supposed to serve. The rule applies whether the flue is clay, metal or another listed material.
We check the outlet on the appliance against the proposed liner before anything is ordered. If the existing flue cannot take a liner of the needed size, you hear that at the assessment. The options then shift to preparing the passage or reconsidering the equipment, and each is priced separately.
An existing metal liner of unknown origin
Some chimneys already hold a metal liner that nobody can identify. Without a label or paperwork, it is hard to know what it was listed for or whether it suits the current appliance. That uncertainty is a reason to assess it rather than assume it is fine.
Look for any tag at the top plate or the appliance connection, and share old invoices if you have them. We explain what we can confirm and what we cannot. Replacing an unidentified liner is one option, and the estimate says why it is recommended when it is.
Spark screens on a liner cap
Many liner caps include a mesh screen that stops sparks and keeps animals out. The code sets requirements for spark arrestors on masonry chimneys, including access for cleaning and a removable screen or cap. The screen must still let flue gases leave freely.
A screen that clogs with deposits restricts the flue. We check the cap during maintenance visits and explain when cleaning is needed. The cap chosen for the liner is named in the estimate, together with its screen. A screen should come off only in the hands of someone who can refit it correctly.
Liner scope written out in full
- Flue route traced from bottom to top
- Damper plate removal where required
- Each flue identified and assigned
- Open chimney covered at each day's end
Liner installation answers in Three Lakes
How long does a relining visit take in Three Lakes?
It depends on the route and the preparation. A straightforward installation can be completed in one visit, while tile removal or glazed deposits add time. We explain the expected sequence when you approve the estimate and tell you if it changes.
Do you install liners for open fireplaces as well as appliances?
Yes. For an open masonry fireplace, the code sizes the flue against the fireplace opening, so the calculation differs from an appliance. We explain which rule set the size in the estimate, along with how the liner leaves the smoke chamber.
Do you leave paperwork about the liner that was installed?
Yes. You receive a written record of the work naming the liner system, the flue it serves, the appliance it was sized for and the parts installed. Keep it with the appliance manual for later visits.
More Ways to Care for Your Fireplace
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
- Fireplace RestorationCoordinate fireplace repairs while preserving suitable existing features and defining the intended use.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
- Smoke Chamber RepairRepair identified smoke-chamber surfaces with the access and material requirements clearly defined.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo