Insulated flue liners fitted in Westwood Lakes
Sizing, insulation and clearances come from the listing and the appliance manual, not from guesswork.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
What points toward a new chimney liner
- Rust holes in an old liner
- Weak draft after an appliance change
- A connector that does not fit the flue
- Soot around the appliance connection
Jump to
A closer look at liner installation
Roof access for a relining job
Relining means working at the chimney top, which means working on the roof. The roof covering has to be protected where ladders, lines and equipment rest. We plan that access at the assessment rather than on installation day.
If the roof has been damaged near the chimney, tell us before the visit. We note anything we see, but roof repairs belong to a roofing contractor. The estimate describes how we reach the chimney and what we protect along the way. Mention any skylights, rooftop equipment or fragile areas near the chimney.
Stainless steel liner installation explained
Stainless steel is a common liner material, but the metal alone does not settle the question. The alloy, the wall form and the listing decide which appliances and fuels it may serve. Two stainless liners can be listed for different uses.
The estimate names the product and its listed application. If a lighter liner is offered for a solid-fuel appliance, ask whether its listing allows that use. We explain our choice and can show where the manual supports it. A product name without its listing tells you very little about what it may serve.
Weather and an open chimney during relining
Rain can interrupt relining work at the top, and an open flue lets water in. We plan the day so the chimney is not left open longer than necessary. Whatever the forecast, an open chimney is covered before we leave.
If weather stops work partway through, we explain what state the flue is in and when the job resumes. The fireplace or appliance stays out of use until the liner is complete. We tell you when it is ready to use again and what to watch for.
Looking up the flue from the fireplace or appliance
The bottom of the flue shows the connection, the damper area and the lower tiles. It also shows how much room there is for a liner to pass. For appliances, the connector and thimble are checked from here.
We explain what we can see from below and what the damper or smoke chamber hides. That limit is written into the findings. If more access is needed to decide, we say what it would take and what it would add to the estimate. Soot patterns at the opening can also hint at how the flue behaves.
Liner scope written out in full
- Liner size matched to the appliance manual
- Cleaning of the existing flue
- Top plate and clamp assembly
- Exclusions listed in plain words
Flue liner answers before you approve
Can two appliances share a single new liner?
Only where the appliance instructions, vent listing and applicable requirements permit a properly sized common vent. Some systems require separate flues. We identify every connected appliance before specifying the liner; the space outside the liner cannot be used as another vent.
What happens to my damper when the liner is installed?
If the liner runs down to an appliance, the damper plate or frame may have to come out for it to pass. The estimate says whether the damper stays or goes, and any damper repair is priced separately from the liner.
What if my appliance needs a vent the chimney cannot provide?
Some appliances vent under pressure or condense their flue gases, and the chimney liner standard excludes those types. Their manuals specify their own vent systems. We explain this before any liner estimate is written, so nothing is bought in error.
More Ways to Care for Your Fireplace
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Chimney Sweep and Chimney CleaningArrange careful chimney cleaning in Miami with a defined scope, protected work area and useful findings.
- Chimney Flashing RepairRepair the chimney-to-roof connection with a scope that accounts for the adjoining roofing and masonry.
- Gas Fireplace Repair and ServiceGet a model-specific gas fireplace service plan for the fault you are seeing or the maintenance your unit needs.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo