Chimney rebuild work from removal to crown in Coral Springs
New courses, a new crown and the flue decision, planned as one project and priced line by line.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Clues that the stack needs reconstruction
- Repairs that keep failing
- Top courses shifted out of line
- Cracks running through several bricks
- Masonry too loose to hold new flashing
Jump to
A rebuild contractor that sets the boundary first
A stack that has moved
Some chimneys tip, twist or pull away from the house. The movement may come from the footing, from a failed attachment to the house or from the top section breaking loose from the masonry below.
A rebuild that simply relays the top on a moving base would not last. We look at where the movement starts and whether it continues below the roof. If the cause lies in the structure, we explain what should be assessed first. The rebuild is then planned around what that assessment finds.
Keeping the stack's shape where it meets the roof
Close to a floor, ceiling or roof crossing, the code keeps a chimney wall and its flue lining at one size and shape. The rule covers a short zone just above and just below each crossing.
When a rebuild starts near the roof line, we keep the new courses in line with the masonry below through that zone. Any decorative change in the top's shape comes higher up, where the code allows it. The estimate describes the shape of the rebuilt top in words.
Why many rebuilds start above the roof
The chimney above the roof has no shelter. Rain, sun and wind reach it on every side, and water that gets past the top soaks its upper courses first. The brick industry notes that chimneys may need repairs sooner than ordinary walls for that reason.
That is why many rebuilds are partial and start near the roof line. The masonry lower down, protected by the roof and the house, often stays sound. We check it before assuming it is, and the estimate says where the evidence puts the start of the rebuild.
Keeping the flue sized for the fireplace
A fireplace needs a flue large enough for its opening to draw well. Florida's building code ties flue size to the size of the fireplace opening. Brick industry chimney guidance ranks flue area and height as the main factors in how a chimney draws.
A rebuild keeps the new flue at a size that suits the fireplace. It should not shrink the flue to save space or material. If the old flue was the wrong size, we explain what the rebuild can change and what would need a different approach.
What the rebuild scope can include
- Top height checked against the code
- Roof covering protection
- Written record of the rebuilt section
- Mortar smears cleaned from finished brick
Chimney reconstruction questions answered
Does the rebuild include a new crown and cap?
A rebuilt top normally gets a new crown, sloped with a drip edge and a bond break around the flue lining. A rain cap is fitted or refitted to suit the flue, and both appear on the estimate.
When can the fireplace be used after the rebuild?
Once the new mortar and crown have cured. The waiting time depends on the materials and the manufacturer's instructions, and we give you the timing in the written record of the work.
What happens to a furnace vent in the chimney during a rebuild?
If a furnace or water heater vents into the chimney, it has to be shut down or disconnected while the flue is open. We plan that step with a heating or plumbing contractor and include it in the schedule.
More Ways to Care for Your Fireplace
- Chimney WaterproofingTreat suitable chimney masonry after checking the surface, repair needs and product requirements.
- Chimney Damper Repair and ReplacementRestore a usable damper mechanism after checking the plate, frame and control linkage.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
Proudly American
Local service. Careful repairs. A fireplace worth coming home to.
Call Now (645) 465-4171We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo