Mortar joint repair for brick chimneys in Spring Garden
Dust, grit and old mortar are cleaned up and hauled away when the job is done.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Mortar wear to mention when you call
- Gaps opening between brick and mortar
- Damp brick inside the attic by the chimney
- Mortar pieces on the roof around the stack
- Stepped cracks following the mortar lines
Jump to
What good tuckpointing looks like
Sand as the key to a mortar color match
Sand is the largest ingredient in mortar, and federal preservation guidance calls it the main source of mortar color and texture. When the sand matches, the rest of the match usually follows. Pigment alone cannot make up for the wrong sand.
We look closely at the existing joints, including grain size and color, before choosing materials. Where the joints have weathered, we compare against sheltered areas that show the original surface. The aim is new mortar that sits comfortably beside the old rather than standing out as a patch.
Filling the deepest joint sections first
Where mortar has failed deep into a joint, the deeper parts are filled before the rest. Federal preservation guidance describes compacting the new mortar into those areas in several layers, bringing them up to the general depth before the joint is finished.
Filling a deep void in one thick pass traps soft mortar behind a hardened skin. That mortar shrinks and can pull away. Working in stages takes longer, and it gives a solid joint from the back to the face. We explain this if your chimney has deep voids.
Packing chimney mortar in thin layers
Brick industry and federal preservation guidance both describe repointing in thin layers. Each layer is pressed firmly into the back of the joint and allowed to stiffen before the next goes on. Most shrinkage happens while each layer hardens.
Layering keeps that shrinkage small and spread out, instead of opening one crack along the face of a thick fill. It is a step that takes patience. We tell you in the estimate that joints are filled in layers, because it affects how long the work takes.
Chimney tuckpointing for homes in Spring Garden
Chimney tuckpointing for homes in Spring Garden follows the same order on every job. We look for the water source, test the joints, choose a mortar that suits the brick and mark the areas that need work. You see all of that before any raking starts.
The work itself is careful and unhurried. Joints are raked to sound depth, filled in layers and tooled to shed water. When we finish, the old mortar is gone, the chimney is clean and you have a written record of the areas we renewed.
Mortar joint checks for homes in Spring Garden
- Raking to an even, sound depth
- Head joints cleared by hand
- Removal of mortar slivers on brick edges
- Access plan for the stack above the roof
Repointing answers for Spring Garden
Will the new mortar match the color of the old joints?
We aim for a close match by choosing the sand and, where needed, a pigment, then comparing samples wet and dry against the existing joints. New mortar often looks brighter at first and settles as it weathers.
What should I do to prepare for tuckpointing at my home?
Clear access to the chimney base, move vehicles away from that side of the house and keep pets indoors. Tell us about plants, vents or fragile roofing near the chimney. We handle protection and cleanup.
Can you match a joint profile that has worn away?
We look for sheltered spots where the original profile survives, such as under the crown overhang. Where brick edges are worn, the new joint may sit slightly back from the face to avoid a thin, fragile edge.
More Ways to Care for Your Fireplace
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Chimney Crown RepairRepair the damaged chimney top with an approach matched to the crown and supporting masonry.
- Chimney Masonry RepairRepair affected chimney brickwork and joints with materials selected for the construction already in place.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo