A wood insert fitted to your fireplace in Weston
At handover you get the manual, the serial number on record and a clear walk-through of the air control.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
Reasons to consider a wood insert for your fireplace
- Smoke puffing from an existing insert
- Soot on the face above the opening
- A second appliance sharing the flue
- A hearth too short for an insert
Jump to
Installing a wood insert the way its manual intends
Emission limits shown on the label
Current wood inserts carry a label showing the emission standard they meet. One maker's manual states that its insert meets the EPA 2020 emission limits for wood heaters. Low emissions in practice depend on dry wood and correct operation as well as on the design.
We show you where the label is on the model you choose and what it says. Keep the manual, because it explains how the insert was tested and how to run it cleanly. We describe emissions only as the label states them.
The first fire after the job is complete
Manuals describe the first fire as coming after the installation is complete and, where required, inspected by the local authority. Before that fire, the owner should understand the air control and the loading steps. Rushing the first fire leaves questions unanswered.
We finish the installation, complete the handover and answer your questions before you light it. If a building or fire official needs to see the work, we explain when that happens. The first fire is then yours to enjoy with the manual in hand.
Local officials and insert installations
An insert manual may tell owners to check with building or fire officials about local restrictions and whether an installation inspection is expected. Answers differ from one job and jurisdiction to the next, so we treat each insert project on its own facts.
Raise the question of review at the free inspection, and we explain how it could shape the schedule. Where an inspection must happen before the first fire, we tell you when and what the inspector is likely to look at. Lighting the insert waits until that step is complete.
Firebrick inside the insert itself
Many inserts line their firebox with their own firebrick, separate from the masonry fireplace around them. Those bricks wear with use and can crack. The manual shows how they sit and which replacement bricks to use. Some manuals allow the bricks to come out to lighten the unit for installation.
We check the insert's firebrick during maintenance visits and explain when replacement is sensible. Bricks inside the insert are ordered from its parts list, not cut from ordinary firebrick. The fireplace's own firebox repair is a separate matter, handled before the insert goes in.
Confirmed before a wood insert is ordered
- Appliance connector and high-temperature sealant
- Floor protection with the right thermal rating
- Blower outlet coordination with an electrician
- Break-in fire guidance at handover
Asked before a wood insert goes in
Does the insert blower need its own outlet?
The optional blower plugs into a grounded outlet near the fireplace. If none is suitable, an electrician adds one as a separate item. We coordinate the location so it suits the manual and is easier to reach before the faceplate goes on.
Is a wood insert allowed in a factory-built fireplace?
Only when both the fireplace's listing and the insert's manual allow the pairing, and many do not. We read both labels during the inspection and explain what they say before you consider any model.
How close can furniture sit to a wood insert?
The manual for your model sets the clearances and the protected floor area, and furniture belongs outside them. We point out those zones at handover. Keep rugs, cushions and stored wood out of the area in front of the loading door.
More Ways to Care for Your Fireplace
- Chimney RebuildRebuild the affected chimney section with the retained structure, roof connection and passage included in the plan.
- Prefab and Zero-Clearance Fireplace RepairIdentify and repair manufactured fireplace components using the appropriate model information.
- Gas Fireplace VentingAssess and repair the gas fireplace vent arrangement using components suited to the identified system.
- Chimney Cap Installation and ReplacementProtect the chimney opening with a cap chosen for its fit, attachment and compatible system.
- Chimney Leak RepairFind the chimney water entry point and plan a repair before restoring the damaged finish.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo