New fireplace installation in Edgewater, framing to first fire
Book the agreed installation no later than 72 hours after your free inspection and save 10% on it.
- Owned and run locally
- Available for same-day service
- Fully licensed and insured
- Family owned and run
When a new fireplace is the right call in Edgewater
- Old chimney pipe with separated joints
- A blank wall where a fire belongs
- An old unit that fails its listing
- A second fireplace for another room
Jump to
Installation decisions for a wood fireplace in Edgewater
The chimney belongs to the fireplace listing
The safety standard for factory-built fireplaces covers the unit together with its chimney, roof parts and related pieces as one tested system. The code repeats the point for the chimney. It is part of the appliance, not an accessory chosen separately.
We install the chimney sections, firestops and termination named in the fireplace manual. If a supplier offers cheaper pipe from another maker, we explain why it cannot join the system. Staying within the listing protects the fire safety of the whole installation.
An insulation shield in the attic
Where a factory-built chimney passes through an insulated attic, the code calls for a metal insulation shield around the pipe. The shield keeps loose or blown insulation away from the chimney and holds the air space open. Listed systems supply their own shield with its own instructions.
We fit the shield and check the insulation around it before leaving the attic. If more insulation is blown in later, the installer needs to know the shield is there. Mention any planned insulation work, and we note the shield location on your written record.
Installing during new construction or a renovation
With the walls open, a fireplace installation is simpler to plan and to inspect. The framing, chimney path and the duct for outside air can go in before insulation and drywall. Sequencing matters, because a fireplace framed after the drywall usually means tearing some of it out again.
Share your construction schedule and drawings, and we fit the fireplace steps into it. We tell your general contractor when each stage should happen and what must stay open until it is checked. That coordination is part of our scope, and so is saying when a stage is ready.
What we look at during the free inspection
For a new fireplace, the free inspection covers the room, the floor structure and the wall you prefer. It also covers the ceiling and attic framing, the roof exit and the side of the house for outside air. For a replacement, we add the old unit, its chimney, the enclosure and the hearth.
You leave the visit knowing which options fit and what each would involve. The written estimate follows with separate items and no commitment. Tell us about any drawings, plans or model preferences beforehand, so the visit covers them.
The fireplace installation scope, item by item
- Chimney route from firebox to roof
- Chase framing for an exterior chimney
- Electrical coordination for a blower kit
- Separate pricing for each installation item
Asked before a fireplace installation in Edgewater
How soon can we light the new fireplace?
After the installation is complete and any required inspection is done. The early fires should be moderate so the paint and refractory can cure, as the manual explains. We go through the lighting routine with you at handover.
Would a wood insert be a simpler project than a new fireplace?
If you already have a sound masonry fireplace, an insert may be simpler. It uses the existing firebox with its own liner. Our fireplace insert installation service handles that, and we explain the difference during the free inspection.
How long does a fireplace installation take from start to finish?
It depends on the type. A factory-built installation moves through framing, the unit, the chimney, the roof and the hearth, while masonry needs more time between stages. The estimate sets out the sequence and the expected schedule.
More Ways to Care for Your Fireplace
- Chimney Liner Installation and ReliningPlan a compatible chimney liner installation with the existing passage, connections and maintenance access considered together.
- Chimney Chase Cover ReplacementReplace the chase top with a properly planned cover and clearly defined pipe connections.
- Top-Sealing Damper InstallationFit a top-mounted damper only after checking the fireplace, product restrictions and control route.
- Gas Fireplace InstallationCreate a complete gas fireplace installation plan for the room, appliance and connected systems.
- Hurricane and Storm Damage Chimney RepairAssess storm-related chimney concerns and distinguish temporary protection from permanent component repair.
We received your request
Our team will contact you to arrange your inspection.
Chimney & Fireplace Brands We Work With
DuraVent 
Olympia Chimney and Venting 
Copperfield Chimney Supply 
Rutland 
Heatilator 
Heat & Glo